 | | Re: 12 Tooth bevel gear case
|
|
(...) I hadn't even thought about it. I can use the wheels. Are they build much stronger than the bevel gears? That is a very good idea. Thank you! Adam (16 years ago, 6-Oct-08, to lugnet.technic)
|
| |
| | Re: Concept car
|
|
(...) See (URL) ;o) Philo (16 years ago, 6-Oct-08, to lugnet.build, lugnet.technic, FTX)
|
| |
| | Re: Concept car
|
|
(...) So it means you were a TECHNIC designer at TLG? Didn't know about. (16 years ago, 6-Oct-08, to lugnet.build, lugnet.technic, FTX)
|
| |
| | Re: 12 Tooth bevel gear case
|
|
(...) Yes! These are the right "gears" for high demanding torque applications. Specially just in front of motors where usually the torque is higher for common designs. (16 years ago, 6-Oct-08, to lugnet.technic)
|
| |
| | Re: 12 Tooth bevel gear case
|
|
(...) Would you have room enough to use the knob wheel ((URL) This one doesn't slip or break... Philo (16 years ago, 6-Oct-08, to lugnet.technic)
|
| |
| | Re: 12 Tooth bevel gear case
|
|
(...) The case/holder that breaks the gears is this one. (URL) project is to try to make A Deere 318, using the power functions medium motor. I have a 9x gear reduction after the motor, before my home made case, which allows the bevel gears to (...) (16 years ago, 5-Oct-08, to lugnet.technic)
|
| |
| | New MOC - Dump truck
|
|
Hello all. After almost a year (on and off) of design and construction, I feel that I am ready to share my latest creation. Read all about it here: (URL) see the pictures here: (URL) short, I've built a dump truck that uses three motors to control (...) (16 years ago, 5-Oct-08, to lugnet.technic, lugnet.announce.moc)
|
| |
| | Re: 12 Tooth bevel gear case
|
|
(...) The 12-tooth bevel gears are not very strong to begin with. If your gears are snapping then maybe you could try using the 12-tooth double bevel gears. (URL) can build a fairly strong housing for these gears by using 4 of this part (URL) to (...) (16 years ago, 4-Oct-08, to lugnet.technic)
|
| |
| | Re: 12 Tooth bevel gear case
|
|
(...) You mean this one? (URL) never had a problem using that, but I've never tried transmitting a lot of torque through 12t bevel gears either. If that fails, maybe you could try (URL) or (URL) luck ROSCO (16 years ago, 3-Oct-08, to lugnet.technic)
|
| |
| | 12 Tooth bevel gear case
|
|
I am having the hardest time coming up with a gearbox that allows a 90 degree turn using the 12 tooth bevel gears or conical wheels. Every time i try to make one, the gears skip, or simply snap. Does anybody have a small, simple, home made version (...) (16 years ago, 2-Oct-08, to lugnet.technic)
|
| |
| | Re: Concept car
|
|
(...) Thanks! (...) The driving rings have nothing to do with the engine, which is a separate unit and can be placed either in the front or back, just like with the 8448. The driving rings are there to change to front wheel or rear wheel drive, but (...) (16 years ago, 30-Sep-08, to lugnet.build, lugnet.technic, FTX)
|
| |
| | Re: Concept car
|
|
(...) It's nice to know that the new parts are there, but so far I have no plans for an Ldraw model. It would take me quite some time, especially with all those weird angles that you get in many Technic models. Nate (16 years ago, 29-Sep-08, to lugnet.build, lugnet.technic)
|
| |
| | Re: Concept car
|
|
Awesome. Even though it has pins of blue, i'd buy one... or two. Steve. (16 years ago, 30-Sep-08, to lugnet.build, lugnet.technic, FTX)
|
| |
| | Re: Adder-substractor module with the new 3L differential
|
|
(...) Yeah! Why shouldn't it work?... Specially after seeing it done... ;D At least it make me to better realize how it works. When it comes to differentials, it is always better to try than trying to figure out how it behaves. (16 years ago, 29-Sep-08, to lugnet.technic)
|
| |
| | Re: Concept car
|
|
Fabulous work!!! From the bottom I see two driving rings near the front and rear differentials. These are used to tweak the motor assemble position and the front/rear drive options. Correct!? Something more for my TechnicBRICKs posting queue... :-) (...) (16 years ago, 29-Sep-08, to lugnet.build, lugnet.technic, FTX)
|
| |
| | Re: Concept car
|
|
(...) Awesome! What about a LDraw model? I just finished the new differential and wishbone ;o) (URL) (16 years ago, 29-Sep-08, to lugnet.build, lugnet.technic)
|
| |
| | Concept car
|
|
Hi! Finally after more than a month, I think it's time to present the result of this project: (URL) It probably has some similarities with the 8448 car, but it's executed in the nowadays technic style with new elements like the differential and (...) (16 years ago, 28-Sep-08, to lugnet.announce, lugnet.build, lugnet.technic, FTX) !
|
| |
| | Adder-substractor module with the new 3L differential
|
|
I read somewhere that the new differential was not good to build an adder-substractor... so I was forced to try! Here is the result: (URL) movie: (URL) (16 years ago, 17-Sep-08, to lugnet.technic)
|
| |
| | Re: New Crane...
|
|
(...) No load tests as of yet. I just got back from BrickFair. (URL) assembled it inside for the first time. I have built the first part of the spreader, which can be seen here: (URL) still have a bit of work left to do in order for it to be (...) (16 years ago, 2-Sep-08, to lugnet.technic)
|
| |
| | PnP, an NXT-based "industrial" robot
|
|
OK, I had to post this in rtl because I confess the main inspiration for this was watching Ian's amazing LEGO industrial P&P automations over the years. This isn't nearly as fast as his, but it's the first time I've captured a motion I really like, (...) (16 years ago, 31-Aug-08, to lugnet.org.ca.rtltoronto, lugnet.robotics, lugnet.technic) !
|
