 | | Re: Light sensor question
|
|
(...) With obvious mappings, of course. (...) Put another way, at no point does the red LED on the light sensor light up, and I consistently read the same value from the light sensor, regardless of whether I set the mode to RAW or percent value. In (...) (22 years ago, 15-Jul-02, to lugnet.robotics.rcx.pbforth)
|
| |
| | Light sensor question
|
|
I want to expand the Scheme procedure (get-light-value <sym | num>) where <sym> is one of 'PORT1, 'PORT2, 'PORT3 and num is either 0, 1, or 2 to the FORTH code 128 <port> SENSOR_MODE <port> SENSOR_CLEAR <port> SENSOR_READ <port> SENSOR_VALUE So, if (...) (22 years ago, 15-Jul-02, to lugnet.robotics.rcx.pbforth)
|
| |
| | Re: Aborting from ISR
|
|
(...) This should be : IsISRFree? 'UserISR ['] NoOp = ; of course. (22 years ago, 14-Jul-02, to lugnet.robotics.rcx.pbforth)
|
| |
| | Re: Aborting from ISR
|
|
(...) To remove your program from the UserISR just set 'UserISR to ['] NoOp - or even better: to the previously stored old value. (...) Yes, you just have to read the current value of 'UserISR. If no other program is hooked to the ISR this is the (...) (22 years ago, 14-Jul-02, to lugnet.robotics.rcx.pbforth)
|
| |
| | Aborting from ISR
|
|
Hi, Is there any way of ABORTing the current program from the ISR ? I want to attach a routine to 'UserISR and have it ABORT and then execute POWER_OFF when the off/on button is pressed. I would also like to know whether a user program or the idle (...) (22 years ago, 14-Jul-02, to lugnet.robotics.rcx.pbforth)
|
| |
| | RE: [ANN] pbForth Version 2.1.5 Release and IR Data Tutorial
|
|
(...) Mario, I'm glad that this has fixed the problem. I hope that you are making good progress with pbForth and that you're enjoying yourself... Cheers, Ralph (22 years ago, 9-Jul-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.pbforth)
|
| |
| | Re: [ANN] pbForth Version 2.1.5 Release and IR Data Tutorial
|
|
Hi Ralph, I don't know if you remember, but I had problems with SAVE-SYSTEM (see msg# 508)... until now! Just to let you know, with pbForth V2.1.5 and (more likely) GUI V2.1.3, it works fine! Thanks Mario (...) (22 years ago, 9-Jul-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx.legos)
|
| |
| | RE: [ANN] pbForth Version 2.1.5 Release and IR Data Tutorial
|
|
(...) Stupid cut and paste error on my part. It's fixed now... Cheers, Ralph (22 years ago, 8-Jul-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx.legos)
|
| |
| | Re: [ANN] pbForth Version 2.1.5 Release and IR Data Tutorial
|
|
Hi Ralph, I just tried the latest version and I can't setup the IR port (mine is USB). I get the following message: Error: can't read "portID": no such variable Works fine with the previous version. Thanks Mario (...) (22 years ago, 8-Jul-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx.legos)
|
| |
| | [ANN] pbForth Version 2.1.5 Release and IR Data Tutorial
|
|
The new 2.1.5 Version of pbForth has a minor fix that affected programmers using the MARKER and LEAVE words. Thanks to Alexander Cech of Austria for supplying great bug reports! I recommend you get the new 2.1.3 GUI while you're at it because it (...) (22 years ago, 8-Jul-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx.legos)
|
