 | | Translating NQC 1.x to NQC 2.0
|
|
The next version of RCX Command Center (expect a beta at the beginning of the comming week) will contain a command to translate from NQC 1.x to NQC 2.0. It is not completely fool-proof but seems to work in almost all cases. Mark Overmars (25 years ago, 13-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC 2.0 ready for beta test
|
|
yeah... mostly search-and-replace. Dave Baum wrote in message ... (...) (25 years ago, 11-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: IR-Tower and PowerBook-G3 ?
|
|
(...) Yes, AT is set to ethernet. (...) OK, I'll try that also. BTW, I now have nqc running on my *old* SE/30 (8MB) with a version of MPW I found on ETO-20. Everything seems to work fine. Downloads firmware as well as test.nqc Still mystified by the (...) (25 years ago, 11-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: IR-Tower and PowerBook-G3 ?
|
|
(...) I use the IR tower with a Wallstreet regularly (NQC was developed on my PowerBook), and I haven't had any problems. Did you make sure that AppleTalk is either set for Ethernet or turned off completely? You also may want to disable other (...) (25 years ago, 11-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: IR-Tower and PowerBook-G3 ?
|
|
(...) Yes. The PB-G3 is plugged into a wall-wart almost all the time. I thought of that also. Very strange. I'm resurecting an old SE/30 in the hopes that I can squeeze MPW into an 8MB machine. I think the serial ports on that machine ought to be (...) (25 years ago, 10-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
| | RE: IR-Tower and PowerBook-G3 ?
|
|
(...) This might sound stupid, but did you try it with the G3 attached to a wall wart? The reason I mention this is that my digital camera only downloads to my laptop if the laptop is plugged in to the wall. The laptop serial levels DO change (...) (25 years ago, 10-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
| | IR-Tower and PowerBook-G3 ?
|
|
Has anyone else had problems using the IR-Tower with a PowerBook-G3 (WallStreet '98)? I tried for two days and only got 'Problem talking to IR device' messages. Tried different cables, cont-checked both cables. Finally went and tried it on the GFs (...) (25 years ago, 10-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC 2.0 ready for beta test
|
|
(...) Many of the changes were to make NQC similar to RCX Code (at least for the commands that RCX Code supports), and I believe RCX Code has a loose connection to the Lego Logo work. Dave (25 years ago, 10-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC 2.0 ready for beta test
|
|
These new commands seem like Lego Logo. Dave Baum wrote in message ... (...) (25 years ago, 9-Aug-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC 2.0 ready for beta test
|
|
I don't have any plans to write such a tool. Really quite a lot of work to build something stand-alone to do this. Should be reasonably easy from within perl, though. Dave (...) (25 years ago, 9-Aug-99, to lugnet.robotics.rcx.nqc)
|
