 | | Re: problem with control speed using NQC
|
|
I think that output power effects the modulation of the motor power. The motor power cycles on and off with the off time being longer at lower power settings. As David stated, this results in the same speed of the motor when it is unloaded for all (...) (25 years ago, 21-Jul-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: problem with control speed using NQC
|
|
I've had the same result. It seems an **unloaded** motor always runs at full speed. To explain it to myself, I've theorized that the 'p' (power) in Fwd() and OutputPower() is more akin to force and does not directly control velocity. Waiting for (...) (25 years ago, 21-Jul-99, to lugnet.robotics.rcx.nqc)
|
| |
| | problem with control speed using NQC
|
|
Okay, need some more help. I have the following code running. My expectation is that the speed of the motor would increase but the integer value in the 'Fwd' command doesn't seem to make any difference. The motor always runs at full speed. (...) (25 years ago, 21-Jul-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC 1.3 released - Command Center?
|
|
(...) simple (...) has been released, check out his home page at: (URL) d/l it directly at: (URL) ya go. m. (25 years ago, 12-Jul-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Joystick Buttons
|
|
Has anyone figured out a way to utilize the buttons on the joystick? like maybe control another motor on top of the bot to turn an arm or something like that? -- Clay Aucoin (25 years ago, 7-Jul-99, to lugnet.robotics.rcx.nqc)
|
| |
| | RCX Command Center Version 2.3
|
|
I am happy to announce the availability of version 2.3 of RCX Command Center. RCX Command Center is a Windows (95, 98, NT) program that assist you in programming the Lego MindStorms and Cybermaster Robots. It provides a higher level interface to the (...) (25 years ago, 19-May-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
|
| |
| | Re: Does NQC support arrays?
|
|
Depending on what the value in the array needs to be you could use a bitmap (e.g. if you want to store true/false to denote the presence of something)... you could then represent the decimal value of the "array" of ones and zeros ... so, for (...) (25 years ago, 18-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Does NQC support arrays?
|
|
Hari Wiguna <hari@mindvision.com> wrote in message news:FBx2nH.B42@lugnet.com... (...) Nope, it doesn't. This is due to a limitation in the RCX environment. If it did support arrays you could have a max of 32 elements (assuming you didn't have any (...) (25 years ago, 18-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Does NQC support arrays?
|
|
I'm building a BrickCode Reader. Basically it reads a stack of 2x2 bricks of various colors like a barcode. I've managed to hack together a prototype BrickCode Reader. I can feed it a stack of bricks and it beeps different tones based on which color (...) (25 years ago, 18-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC 1.3 released - Command Center?
|
|
(...) [snip] (...) DOH! Yup. I've gotten quite fond of the RCXCC/NQC combination. It handles just about anything that I have thought up so far! DLC (25 years ago, 14-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC 1.3 released - Command Center?
|
|
(...) I assume you meant "RcxCC". Last I heard from Mark, it will be "soon". I'm pretty sure you can just replace nqc.exe and rcx.nqh in RcxCC with the 1.3 versions. There won't be templates/hilighting for any new commands, but at least you will be (...) (25 years ago, 12-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC 1.3 released - Command Center?
|
|
(...) Say, when will NQCCC 1.3 be released? I'm completely hooked on the simple environment. DLC (25 years ago, 11-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: two task and while true
|
|
(...) Hmm: - I believe that, after main starts, unless you press IN_3 *very* quickly, that IN_3 will not be 1, hence stop wb will be chosen. Perhaps you want something like this? : task main { while (true) { wait(IN_3 == 1); // start motor wait(IN_3 (...) (25 years ago, 7-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: communication Linux - NQC - Cybermaster
|
|
(...) Yep, NQC assigns from 0 up. The listing (use -L) will print out the variable cross reference for an NQC program. Dave (25 years ago, 5-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: communication Linux - NQC - Cybermaster
|
|
(...) Thanks for your suggestions. Say, just what is variable 0? The first variable assigned? I should probably try to read some more about the internals of the RCX/Cybermaster, I suppose. Fredrik (25 years ago, 4-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: communication Linux - NQC - Cybermaster
|
|
(...) You can probably do anything you want with the [minimally documented] -raw option for nqc. You can use it to send arbitrary packets to the RCX or Cybermaster. For example, to query variable 0, you could do this: nqc -c -raw 120000 Of course, (...) (25 years ago, 2-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | communication Linux - NQC - Cybermaster
|
|
I'm running NQC on a Linux system. Is there any way to communicate between the computer and the Cybermaster mobile unit using this software? Or are there any other types of software I might consider to do this? Fredrik (25 years ago, 2-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: JAVA and Cybermaster ?
|
|
(...) Question: Why do you want to use JAVA with the CyberMaster? JAVA is similar to C++, which is was developed from C and which is the base language of NQC. What are you expecting to do with JAVA that can not be made with NQC? And if you are in a (...) (25 years ago, 2-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | JAVA and Cybermaster ?
|
|
I saw some Java stuff for the RCX. Is there soemthing for the Cybermaster? Stefan -- ***...*** Stefan Prescher prescher@hermes.fho-emden.de (25 years ago, 2-May-99, to lugnet.robotics.rcx.nqc)
|
| |
| | two task and while true
|
|
Hi I made a small programm task main if IN_3 ==1 start wb else stop wb task sb while (true) if () fwd(Out_a,7); I found out that the prgramms goes into the while loop but it never started the motor if I copied it into the main part it runs fine Is (...) (25 years ago, 2-May-99, to lugnet.robotics.rcx.nqc)
|
