To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.robotics.rcx.legosOpen lugnet.robotics.rcx.legos in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / RCX / legOS / 3493 (-10)
  Re: BrickOS motor port horrors
 
(...) Rob, I've had the same problem with BrickOS. The installation I used came with BrickOS already built. I reloaded the RCX with LEGO firmware and all three motor ports worked fine. I concluded it was a BrickOS problem that I would wrestle with (...) (21 years ago, 26-Oct-03, to lugnet.robotics.rcx.legos)
 
  Re: BrickOS motor port horrors
 
(...) That is the part that really bites me. Are you able to reproduce the error? If yes, try to put out the batteries for a longer time. Anyway, it seems worthwile to have a look at the brickOS initialization code for the motors. If you can (...) (21 years ago, 26-Oct-03, to lugnet.robotics.rcx.legos)
 
  Re: BrickOS motor port horrors
 
Well, I don't know much about it being possessed, but you should try to divide the problem probabilities in half. Try loading the original lego firmware. (Yes I know, this brings horror to some of you fellow programmers out there, but its just (...) (21 years ago, 26-Oct-03, to lugnet.robotics.rcx.legos)
 
  BrickOS motor port horrors
 
I was writing some simple programs to test out BrickOS last night, and had some really strange behavior. I hooked up a motor to port B and a rotation sensor to port 2. My programs were just testing out various motor speeds and positioning accuracy. (...) (21 years ago, 25-Oct-03, to lugnet.robotics.rcx.legos)
 
  lnpd+liblnp + brickos-0.2.6.10
 
It seems to be not possible to use lnpd+liblnp with brickos-0.2.6.10. Is there a patch available to get the liblnp package to work? (21 years ago, 22-Oct-03, to lugnet.robotics.rcx.legos)
 
  size limit on the programs for the RCX
 
is there a size limit for our program? Like it cannot exceed a certain amount... by that i mean, if i have say several programs, is there a limit on how much each could size so that i can fit them all on the RCX at once and be able to run? because (...) (21 years ago, 22-Oct-03, to lugnet.robotics.rcx.legos, FTX)
 
  Re: Strange error message I have recieved
 
(...) Thanks a lot, it worked. I knew it had something to do with the memory. Mike (21 years ago, 20-Oct-03, to lugnet.robotics.rcx.legos)
 
  LNP and USB over linux
 
Hi, I recently finished my thesis project: "Constraint Programming over LEGOS MindStorm" working with LNP, Serial tower(the only one i found sopport) and a rcx 2.0. I would like to know if somebody knows about LNP SUPPORTING USB. I already have the (...) (21 years ago, 20-Oct-03, to lugnet.robotics.rcx.legos)
 
  Re: Strange error message I have recieved
 
(...) Check out this message, it might address your problem: (URL) (21 years ago, 20-Oct-03, to lugnet.robotics.rcx.legos)
 
  Strange error message I have recieved
 
I am in the process of completing my senior project where I will add 3 additional allocation algorithms to the Memory Mangament facility in BrickOS. I should the Next Fit algorithm done but when I add a certain part of code I get the following error (...) (21 years ago, 19-Oct-03, to lugnet.robotics.rcx.legos)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR