 | | Re: Float and int
|
|
(...) int is 16 bits, big endian, signed. It goes from -32768 to 32767. unsigned int goes from 0 to 65535. char is 8, long is 32, long long is 64, with the standard limits. Floats and doubles are emulated in software, as the H8/300 processor has no (...) (22 years ago, 30-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Float and int
|
|
Does anyone know what the maximum and minimum size of integer which can be stored is? Likewise, what is the floating point accuracy of BrickOS for variables of type "float" and "double" (is there such thing in BrickOS?) ? Both of these questions (...) (22 years ago, 29-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | USB IR tower support in Lunix
|
|
I have seen some past messages in this forum regarding the support for the USB IR tower in the Linux version of BrickOS. However, it seems that nothing have been added recently to the CVS tree at SourceForge. Is somebody working on this project (...) (22 years ago, 20-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: linker segmentation fault
|
|
(...) Workaround attached. Brickos maintainers: Any comments? Maybe put something vaguely like it into CVS? Max. (22 years ago, 17-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | linker segmentation fault
|
|
I'm running Red Hat Linux 8.0 (gcc 3.2 and binutils 2.13). Whe I try to compile the demos that come with brickOS 0.2.6.09, using binutils 2.12.91 for the cross-linker and gcc 3.2.1 as cross-compiler, the linker crashes. Here is the output of the (...) (22 years ago, 17-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOS Threading...
|
|
(...) To tell you the truth, I'm not exactly sure how the BrickOS PWM works, but I do know the standard RCX PWM simply switches the motors between ON and FLOAT, which will not slow the motor down, when it switches from a high power, to a lower (...) (22 years ago, 16-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: sys_time (long post)
|
|
Only a suggestion, In any processor architecture (with or without disabling or recursive interrupts) when I need to read timers with more than 1 single instruction I do the following: Read the timer (both low and high value) until I get 2 times the (...) (22 years ago, 16-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: sys_time (long post)
|
|
(...) I went back and read... I was missing something apparently... Note to self... do not skim. -Kekoa (22 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: sys_time (long post)
|
|
Does the H8 let an interrupt interrupt an interrupt? (Or at least the interrupts that matter in this case?) You two might want to check on that. It would seem the code is safe if the answer to the first question is no... ? Maybe I'm missing (...) (22 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOS Threading...
|
|
Joe, (...) Maybe a special kernel build for testing purposes that increments the lower sys_time word by 0x4000 instead of 1. This will greatly increase the opportunity for this glitch to occur (from once every 65 seconds to once every 4ms.) You (...) (22 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
