 | | Re: Question about mm.C in BrickOS
|
|
(...) Michael I was reading through your reply you sent me a while back and I don't understand what that line in the code does and you explaination of it. I don't understand what is meant by pointing behind the block. Any help would be great thanks. (...) (21 years ago, 14-Sep-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Setup sensor type using LegOS Commands Reference 1.0-0.2.4
|
|
There is a tutorial no ? nanobapt (...) (21 years ago, 14-Sep-03, to lugnet.robotics.rcx.legos)
|
| |
| | Setup sensor type using LegOS Commands Reference 1.0-0.2.4
|
|
Dear all, Can you please tell me how I can select a sensor type using the LegOS Commands Reference 1.0-0.2.4? Regards Alkis (21 years ago, 13-Sep-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: some measurements in lnp, please comment!
|
|
"Brian B. Alano" <alano@bloomington.in.us> wrote in message news:HL30D6.1rDC@lugnet.com... (...) practical (...) assume 50% (...) think anything (...) I'm not familiar with LNP, but I do have a good handle on infra-red messaging in general. There (...) (21 years ago, 12-Sep-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: some measurements in lnp, please comment!
|
|
(...) Old thread, but oh, well. 4800 baud is 4800 bits per second or 600 bytes per second. If you assume 50% overhead, which is optimistic, that's 300 bytes per second. So I think anything over 200 bytes per second is pretty good. (21 years ago, 12-Sep-03, to lugnet.robotics.rcx.legos)
|
| |
| | RE: leJOS & BricxCC news
|
|
John, Thanks for continuing to work on this. It's one of the things that keeps me motivated to continue supporting pbForth. Now, there has not bee much traffic there lately, and I have not done much with it becuase as far as I know, things are "just (...) (21 years ago, 5-Sep-03, to lugnet.robotics.rcx.java, lugnet.robotics.rcx, lugnet.robotics.rcx.legos, lugnet.robotics.rcx.nqc, lugnet.robotics.rcx.pbforth)
|
| |
| | Re: trouble compiling brickOS
|
|
(...) Hm, that should not happen. Try to start your hitachi compiler by hand, for example with "h8300-hms-gcc --version" to get an "I am alive" message from it, so you are sure it is installed as intended. If _you_ can't get it to work, configure (...) (21 years ago, 5-Sep-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: leJOS & BricxCC news
|
|
In lugnet.robotics.rcx.java, Mark Riley wrote: [snipped] (...) I have incorporated the changes made to firmdl in the leJOS distribution into my BricxCC firmware downloader code. Now I can successfully download all the firmwares I have access to (...) (21 years ago, 5-Sep-03, to lugnet.robotics.rcx.java, lugnet.robotics.rcx, lugnet.robotics.rcx.legos, lugnet.robotics.rcx.nqc, lugnet.robotics.rcx.pbforth)
|
| |
| | Re: trouble compiling brickOS
|
|
(...) I did! (...) It did complain and I did install the hitachi 8300 gcc version. Funny thing, after installing it, the configure script was still complaining that it cannot find the hitachi gcc compiler, although the binaries were right there in (...) (21 years ago, 5-Sep-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: trouble compiling brickOS
|
|
(...) Run ./configure!!! (...) Let me guess: You use the original c compiler of your linux distribution. May be that configure will complain that it does not find the gcc compiler? You run Linux on a Intel box. Your normal gcc will compile c to (...) (21 years ago, 3-Sep-03, to lugnet.robotics.rcx.legos)
|
