 | | Re: Charge!
|
|
(...) I don't think Dave is exactly right, but it is close. (I tested it on my panio.) I believe though that it repeats twice, one octave higher each time. Hope that helps! Cheers, (25 years ago, 24-Nov-00, to lugnet.robotics.rcx, lugnet.robotics)
|
| |
| | Using the RCX to turn on my stero system...
|
|
Hi all, I have a Aiwa RC-ZAS02 remote control. Could somebody either tell me the "blink command" for the power button or how I could find out what it is? Cheers, (25 years ago, 24-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: Using a Sony Remote control to run my Mindstorms...
|
|
(...) How much did you pay for it? The suggested manufacturer's price is $180!! Cheers, (25 years ago, 24-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: I/O port of H8/3000
|
|
(...) Does this mean that a skilled hardware person can open the yellow brick and solder two additional analogue sensors to pins 4 and 5 of the A/D converter on port 7? [and of course violate the LEGO licence thus losing a support and who knows what (...) (25 years ago, 24-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: Newbie Question! How do I pause or stop sensor input.
|
|
(...) Are you using RCX Code or NQC? Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 24-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Mini RADAR or SONAR for the RCX
|
|
Hi, Does anyone know where I could purchase a relatively cheap mini RADAR or SONAR device that I could use with my RCX? Any help will be appreciated. Cheers, (25 years ago, 23-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Newbie Question! How do I pause or stop sensor input.
|
|
Hi, Im building a train turntable with 5 sets of train tracks. I want to be able to activate sensor 1 and have it turn on motor A clockwise for .5 seconds. Once the track has stoped. Manualy activate sensor 2 and have motor A turn counter clockwise (...) (25 years ago, 23-Nov-00, to lugnet.robotics.rcx)
|
| |
| | pbsim 1.0 a2 released
|
|
I've added RCX 2.0 support and filled in a lot of the missing features. There still are a few odds and ends that need to be implemented, but most programs should be able to be simulated on it. This is still only the core simulator and not a full GUI (...) (25 years ago, 19-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: Batteries...
|
|
Yes, it's possible. You get less voltage with NiCads, so the motors don't turn as fast as they do with brand-new alkalines. Plus they don't last as long. However, they're so much cheaper to run! I used to use NiCads during development and general (...) (25 years ago, 15-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: I/O port of H8/3000
|
|
(...) Are they all used? No. See the H8/300 manual and the bottom section of: (URL) visit the Microcontroller Interface section of my horribly-incomplete Low-level RCX Reference, at: (URL) unused pins are better documented in the low-level (...) (25 years ago, 17-Nov-00, to lugnet.robotics.rcx)
|
| |
| | I/O port of H8/3000
|
|
I'm not sure about how many I/O ports the H8/3000 in the RCX has. Are they all used in the RCX? (25 years ago, 17-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: IR download broken
|
|
(...) It requires batteries to be in it all the time. you get 60 seconds with it off and the batteries out. An easy way to tell is that it has 0000 when you turn it on with firmware and only the little man when it doesn't. Dean -- Coin-Op's For (...) (25 years ago, 16-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: IR download broken
|
|
So what causes it to 'forget' the firmware. Doesn't it store it in Flash memory? Or does it require batteries to be installed all the time? Matt (25 years ago, 16-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: IR download broken
|
|
(...) The RCX has 5 programs built into the system when there is no firmware... Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 16-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: IR download broken
|
|
(...) Yep, that was it thanks. How come it forgot the firmware? And how come the programs stored on it were still working? Very strange. Matt (25 years ago, 16-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: IR download broken
|
|
(...) The remote only works when the Firmware has been downloaded. Remove the batteries and download the firmware. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 16-Nov-00, to lugnet.robotics.rcx)
|
| |
| | IR download broken
|
|
I just tried my new IR remote for my RCX and it doesn't work at all. So then I tried downloading a program with NQC (which I have done for quite a while) and that doesn't work either, I just get "No response from RCX". What's going on, is my RCX (...) (25 years ago, 16-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Remote Control Internals?
|
|
Is there any tech. documentation/FAQ's for the remote control? Basically I need to know what it sends to the RCX. Does it send special opcodes, or regular RCX 1 commands? I don't see any remote control ops documented, like there are in the RCX 2 (...) (25 years ago, 13-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: Batteries...
|
|
I use NiMH in RCX/Cybermaster/Code Pilot and towers with no problems. Jürgen (25 years ago, 15-Nov-00, to lugnet.robotics.rcx)
|
| |
| | Re: Batteries...
|
|
(...) Hi Ciaran, since i've got my RCXs (1.0 and 1.5) I use NiCd and NiMHd without any Problems. Rainer (25 years ago, 15-Nov-00, to lugnet.robotics.rcx)
|
