 | | Re: Can the Run button be reprogrammed?
|
|
(...) BrickOS does allow you to configure how the buttons are used. The RUN and Power buttons are read in the BrickOS "firmware", so you'd need to change the kernal, if you want to do other things with them, but it is very possible. So, yes, the run (...) (20 years ago, 9-Feb-05, to lugnet.robotics.rcx)
|
| |
| | Can the Run button be reprogrammed?
|
|
I was just wondering, can the Run button on the RCX be reprogrammed? I was thinking of a theoretical, fail-safe system, where it would be nice to run a clean-up routine after the run button had been pressed to stop the program. I reckon you'd have (...) (20 years ago, 9-Feb-05, to lugnet.robotics.rcx)
|
| |
| | Re: Sending Commands to Spybot from RCX - Question from a Beginner to Comm area.
|
|
Hi Everybody, I have used SendSpybotMsg and SendSpybotCtrlMessage (of course in connection with resopective set messages) without any problems using BCC 3.3.7.5 and 3.3.7.9. These two commands gives RCX a nice control over spybot. Specially (...) (20 years ago, 8-Feb-05, to lugnet.robotics.spybotics, lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
| |
| | Re: a problem ... need some help !
|
|
(...) Although you may not be using BricxCC to compile your leJOS code I think it might be instructive to describe how BricxCC manages to compile leJOS code properly. The way BricxCC works with leJOS is to create a very simple makefile that launches (...) (20 years ago, 6-Feb-05, to lugnet.robotics.rcx)
|
| |
| | Re: a problem ... need some help !
|
|
hi,,, thanks, i just defined JAVAC to where my javac is and its working but there is a small problem that i have to put the java file im compiling in lejos\bin because it doesn't work when i set the CLASSPATH ! i also defined JAVA env var to (...) (20 years ago, 5-Feb-05, to lugnet.robotics.rcx)
|
| |
| | Re: a problem ... need some help !
|
|
On the off-chance you might be trying to use lejos with BricxCC here are a few instructions that should get things working. It has been a while since I tried to use lejos with a recent java SDK and it turns out that the pre-built minimal lejos (...) (20 years ago, 5-Feb-05, to lugnet.robotics.rcx)
|
| |
| | a problem ... need some help !
|
|
hi everyone, im just starting to work with lego RIS2.0 and Lejos, but i have a problem with the lejos setup i did all the instructions and when i tried to compile a java file using the lejosc command i got this reply: Unable to execute javac. Return (...) (20 years ago, 4-Feb-05, to lugnet.robotics.rcx)
|
| |
| | Re: New TLC Mindstorms survey
|
|
(...) I'm not sure what good it'll do if the survey is that old but i took it anyway. BTW hope that release it soon since i''ll soon (i hope) be getting 2.0. I'd hate to get it and then a few months later see 3.0 in the shelfs. (20 years ago, 31-Jan-05, to lugnet.robotics.rcx)
|
| |
| | Re: RCX3 - Can extra hardware functionality be added?
|
|
(...) A friend of mine is actually working on this 'pod' concept. i have been playing with a working prototype and i must say that it preforms very well. and it is SO nice to not be limited on the number of sensor inputs. pictures of the prototype (...) (20 years ago, 31-Jan-05, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
| | Re: Sending Commands to Spybot from RCX - Question from a Beginner to Comm area.
|
|
(...) First of all, my apologies for not answering you via email. I've been a bit busy at work. I needed to run some tests myself before I could properly respond as well. The 0x9223 from the RCX happens to match the IR sent out by the Spybot (...) (20 years ago, 28-Jan-05, to lugnet.robotics.spybotics, lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
