|
|
 | | Re: IR remote control codes.
|
| (...) What exactly do you want to know about this opcode? I have the full documentation in the form of the firmware disassembly... and it is online. See address 9700 of the disassembly at: (URL) you can't find it, search for "d2 opcode handler". I (...) (24 years ago, 6-Nov-01, to lugnet.robotics.rcx)
| | | | | Re: IR transmission, strange coding ?
|
| (...) I forget exactly how I measured this. I think maybe I hooked a scope directly to the LEDs then sent a constant stream of something to the tower and looked at the waveform on the scope. I don't remember noticing anything funny with the start (...) (24 years ago, 6-Nov-01, to lugnet.robotics.rcx)
| | | | | IR remote control codes.
|
| hi all, has anyone experience with the IR codes transmitted by the remote controler. As far as I know, these codes are normal direct commands, which you also send from your PC, using the standard IR tower. The documentation on this issue is not very (...) (24 years ago, 4-Nov-01, to lugnet.robotics.rcx)
| | | | | IR transmission, strange coding ?
|
| hi all, I'm working on what I call an "InfraRed All module" , which should become IR-tower, IR-sensor, IR-audio-remote, etc. Measuring the IR pulses from the IR-tower I encountered the following effects According to what Kekoa Proudfoot found "A '0' (...) (24 years ago, 4-Nov-01, to lugnet.robotics.rcx)
| | | | | RE: Code-only Line-tracking competition
|
| (...) David, thanks for putting this contest on. I admit that I was intrigued when it was announced but did not have time to put an entry together. The idea of a code-only competition on a standard hardware platform is brilliant and opens up the (...) (24 years ago, 28-Oct-01, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.events, lugnet.org.us.smart)
| | | | | Re: Code-only Line-tracking competition
|
| Well, it's been a few weeks since the Workshop 3D RCX Challenge, and all the other results were in a long time ago, but we finally have the results for the code-only event. Since tab characters seem to disappear in these posts, and a table is (...) (24 years ago, 28-Oct-01, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.events, lugnet.org.us.smart)
| | | | | A RCX Switch Shed
|
| I created a RCX Switch Shed that can be used to control Train Switch Point by legOS or NQC, please check (URL) (24 years ago, 26-Oct-01, to lugnet.trains, lugnet.town, lugnet.robotics.rcx)
| | | | | Re: inverted penulum
|
| Developing our inverted pendulum project we tested today the power of the vehicle which we designed for the purpose. It looks like the Acrobot, but with twice the first part, so that each wheel is powered by a motor. Both motors of one side are (...) (24 years ago, 23-Oct-01, to lugnet.robotics.rcx)
| | | | | What is a typical Mac here?
|
| Hi all, I'd like to know what constitutes a typical Mindstorms Mac system. I'm trying to verify my new pbForth system, and it runs (slowly) on a PPC 6100/60 and pretty darn good on a G3/240 I'm considering getting a used PPC/180 to test with, but I (...) (24 years ago, 23-Oct-01, to lugnet.robotics.rcx)
| | | | | Re: Photos of my MOCs
|
| My page is cleared, no any popup ad to trouble you again! Zhengrong (...) (24 years ago, 20-Oct-01, to lugnet.trains, lugnet.robotics.rcx)
|
|
