 | | RE: multiplex 2 touch sensors on a single RCX port
|
|
Sorry, I don't mean the duration, not hysteresis. -----Original Message----- From: news-gateway@lugnet.com [mailto:news-gateway...ugnet.com] On Behalf Of Elizabeth Mabrey Sent: Monday, June 02, 2008 6:11 PM To: lugnet.robotics.rcx....lugnet.com (...) (16 years ago, 3-Jun-08, to lugnet.robotics.rcx.robolab)
|
| |
| | multiplex 2 touch sensors on a single RCX port
|
|
I have these 2 touch sensors multiplexing on the same input port. Their raw values are 47 and 39. I tried to set up 2 separate events, one for the range of 45 to 50 and another one for 35 to 40. However, the one for the lower feedback often set off (...) (16 years ago, 2-Jun-08, to lugnet.robotics.rcx.robolab)
|
| |
| | Re: Remote control RCX by mobile phone
|
|
Dear Zhengrong Zang I don't thing that this will be work because as far as i know mobile phone's using the irda protokoll like on the pc's to comunicate to mobilephones and other devices. The protokoll is the same: baud parity and stopbit but it (...) (16 years ago, 30-May-08, to lugnet.robotics.rcx)
|
| |
| | Re: RCX Serial Hardware Hack
|
|
Dear Claude (...) A: Thank you for finding the PDF. (...) A: I will check ( measure the Voltage on the IF LEDS) should be approx. 9V betweem LED and Transistor if everything is off. (...) A: Now i had success . It works. (...) I have allready done (...) (16 years ago, 29-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: RCX Serial Hardware Hack
|
|
Dear Matthew (...) A: Now it works with 4800 baud via bluetoothconnection . There was a couple of Problems. 1) At first i tried with the USB Tower but i coult only swith to 4800 bauds but there is no possibilty to change parity. 2) With the serial (...) (16 years ago, 29-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: RCX Serial Hardware Hack
|
|
"Claude Baumann" <cbaumann@ci.educ.lu> wrote in message news:K1E031.y4@lugnet.com... (...) I was able to retrieve it from archive.org - (URL) . (16 years ago, 28-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | Remote control RCX by mobile phone
|
|
I try to make a appli that executed in mobile phone, it can control RCX. The mobile phone's SDK provides class RemoteControlData with some methods as below: setPulse(int leader_on, int leader_off, int trailer_on) leader_on: start bit High period (...) (16 years ago, 27-May-08, to lugnet.robotics.rcx)
|
| |
| | Re: RCX Serial Hardware Hack
|
|
(...) The carrier should be quiet in any case, because it disturbs the TX signal. (...) We tried this,but it didn't work. Why, because the transistor will drain some current, if the emitter has positive voltage and the base goes low. If the carrier (...) (16 years ago, 24-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: RCX Serial Hardware Hack
|
|
Glad to hear it is working--thank you for the update. If I may ask, I have a few questions-- * So if I understand these posts correctly, 4800 baud now works with the IR connection and not just with the hardware hack? *A couple posts from Dick Swan (...) (16 years ago, 24-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Success
|
|
Hi I have implemented the stuff // and set the port6<7> pin LOW. Now the upper PNP transistor isn't conducting anymore. Now TX and RX works Here are the program #include <lnp.h> #include <conio.h> #include <string.h> #include <lnp-logical.h> (...) (16 years ago, 20-May-08, to lugnet.robotics.rcx.legos)
|
