| | BricxCC release 3.3.7.10
|
|
(URL) just released BricxCC 3.3.7.10. Lots of stuff is unfinished but it has been forever since my last official release. New Stuff (in part): Version 3.3.7.10 has a revised help system (not entirely complete). It adds support for the new Swan (...) (19 years ago, 4-Oct-05, to lugnet.robotics.rcx)
|
|
| | NQC release 3.1r3
|
|
(URL) a bug in expressions like a = a*2 + a*3; Thanks! John Hansen (19 years ago, 4-Oct-05, to lugnet.robotics.rcx.nqc)
|
|
| | Re: roboarm activities
|
|
(...) I found that either rotating a colour wheel in front of the sensor(with its distance LED off) in combination with a white light -or- using a coloured LED at a _very_ close distance works well; i.e. most materials give a marked response as long (...) (19 years ago, 3-Oct-05, to lugnet.robotics.rcx.legos, lugnet.robotics.rcx.robolab)
|
|
| | Latest version os
|
|
Hi, Can someone post a latest compiled version of the brickos 0.9.0 (BrickOS.srec) I have some trouble to compile this version Thanks, Jan Kromhout Hellevoetsluis-NL (19 years ago, 3-Oct-05, to lugnet.robotics.rcx.legos)
|
|
| | roboarm activities
|
|
Hi, questions to all the guru out there. I have spent 20 hours on this roboarm. I am hoping to make it work like a color sorter. - pick up a ball wrapped in tin foil and drop it off at a container wrapped up in tin foil as well. - pick up a ball (...) (19 years ago, 2-Oct-05, to lugnet.robotics.rcx.legos, lugnet.robotics.rcx.robolab)
|
|
| | Re: error in using brickOS under Bricx Command Center
|
|
(...) Can you do F12 and post the contents (if any)? Do you have bash installed? While the error message is displayed you can open a command prompt and change directory to the location of your source code file. There you should find a .cmd and a (...) (19 years ago, 29-Sep-05, to lugnet.robotics.rcx.legos)
|
|
| | Re: Latest version BrixCC
|
|
(...) I have not yet made an official 3.3.7.9 release of BricxCC. My apologies for the delay. For now you can use the latest version in swan_test.zip. John Hansen (19 years ago, 29-Sep-05, to lugnet.robotics.rcx.nqc)
|
|
| | Re: Can't upload new program after I have used LNP under brickos
|
|
(...) Well, thanks for the help, that didn't actually work. But I found it out, what was my fault. In my Program I changed the LNP Base adress of the robot. After that the robot did not react to the default adress 0. So, at the end of the program I (...) (19 years ago, 29-Sep-05, to lugnet.robotics.rcx.legos)
|
|
| | Latest version BrixCC
|
|
Hi, I found on the sourceforge.net the Brixcc version 3.3.7.7 and in the swan_test.zip the version 3.3.7.9. Is there a newer version? Regards, Jan Kromhout Hellevoetsluis-NL (19 years ago, 27-Sep-05, to lugnet.robotics.rcx.nqc)
|
|
| | Enchanced Firmware
|
|
Hi, Can someone tell me wath the status is of the Enhanced Firmware? and the latest version of BrixCC? Regards Jan Kromhout Hellevoetsluis-NL (19 years ago, 27-Sep-05, to lugnet.robotics.rcx)
|