 | | Announcing Full Throttle - Control LDCC From Windows
|
|
I have just released (URL) version 1.00> of a program that I call Full Throttle. This Windows application uses your Mindstorms IR tower (either serial or USB) to communicate with an RCX that is running (URL) Mark Riley's LDCC replacement firmware> (...) (21 years ago, 4-Aug-03, to lugnet.trains, lugnet.robotics.rcx, FTX) !!
|
| |
| | Re: Problems with BrickOS installation
|
|
(...) I would recommend using the pre-built Hitachi tools which are still available from my BricxCC website. (URL) simpler than trying to download all the right versions of the GCC source code. John Hansen (21 years ago, 4-Aug-03, to lugnet.robotics.rcx.legos)
|
| |
| | Problems with BrickOS installation
|
|
Hi, I'm following these directions explicitly: (URL) installed just fine. When I run buildgcc.sh it dies trying to assemble libgcc1.S. The comments at the top of the file cause syntax errors. The comments are dilineated with ";;". How can the (...) (21 years ago, 3-Aug-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Robolab upgrade to 2.5.3 and other things
|
|
(...) Unfortunately the Service Pack 1 does not seem to work properly to upgrade from 2.5 to 2.5.2. The best way is to get a copy of the current Robolab ver 2.5.2 which is called "ROBOLAB with Training Missions" from your local LEGO distributor. (...) (21 years ago, 3-Aug-03, to lugnet.robotics, lugnet.edu, lugnet.robotics.rcx.robolab, lugnet.robotics.edu)
|
| |
| | Re: light sensor question
|
|
(...) I've done a lot of readings with the light sensor and analysed them. If you want to have a look you can go to (URL) . If you look in the appendix of that document you'll find information on the light sensor (and many other things...) Magdalena (21 years ago, 31-Jul-03, to lugnet.robotics.rcx)
|
| |
| | USB2 and IR-Tower problem
|
|
Hi, I was just wondering if anyone here had experienced any problems using the IR-tower on a USB2 port? My university has just upgraded 20 of the pc's used for the Lego, the previous setup worked fine and the tower was attached to just a normal USB (...) (21 years ago, 30-Jul-03, to lugnet.robotics.rcx)
|
| |
| | Pneumatic Presure sensor
|
|
Mindsensors Has recently developed a low cost pressure sensor, which measures pressure up to 35 Psi (241 Kg/scm) using Motorola Pressure sensor. If your are interested visit us at www.mindsensors.com/pps.htm www.mindsensors.com Mindsensors Robotics (21 years ago, 30-Jul-03, to lugnet.robotics.rcx)
|
| |
| | Re: light sensor question
|
|
(...) A friend of mine suggests that the poor response of the sensor to the LED is because the light from the LED is a single color. Where as the light from the incandescent bulb is white light which apparently contains many if not all of the (...) (21 years ago, 29-Jul-03, to lugnet.robotics.rcx)
|
| |
| | Re: LEGO remote controller problem
|
|
(...) Then this is the first time ;) It was indeed the compiler. Using those versions you named in your message, my compiled brickOS.srec file works as well. The lr_startup and lr_shutdown calls don't make any difference, whether they are in or out. (...) (21 years ago, 29-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: LEGO remote controller problem
|
|
(...) Great. (...) I use h8300-hms-gcc-3.1-1.i386.rpm h8300-hms-binutils-2...1.i386.rpm but I never heard from anyone that some gcc version produces a bad brickOS system. Strange, indeed. Regards, Michael (21 years ago, 28-Jul-03, to lugnet.robotics.rcx.legos)
|
