 | | Re: where to buy individual parts?
|
|
In lugnet.robotics.rcx, Zhengrong Zang writes: There are some problems though... (...) Tends to only offer a very limited range of products (in the UK at least) - trying to get hold of some parts from there, like rotation sensors, seems to be (...) (23 years ago, 30-Nov-01, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: where to buy individual parts?
|
|
Hi, Try (URL) / (URL) luck! Zhengrong (...) (23 years ago, 30-Nov-01, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: COLOR light sensor
|
|
(...) Hi Philo, as I pointed out, Mike has published the color-sensor somewhere in an article. You should send him a mail and ask where you can find the schematics and perhaps the PCboard. Claude (23 years ago, 30-Nov-01, to lugnet.robotics.rcx)
|
| |
| | Re: COLOR light sensor
|
|
Hi Claude, I visited Mike's site and found nothing... where did you see this ? Philo (...) (23 years ago, 30-Nov-01, to lugnet.robotics.rcx)
|
| |
| | Re: Can I use LegOS with CyberMaster?
|
|
(...) That is not possible, the Cybermaster has the firmware in ROM and very little (a few hundred bytes) RAM. (...) It doesn't. (...) The only one is NQC. Jürgen (23 years ago, 29-Nov-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: COLOR light sensor
|
|
(...) (URL) Jürgen Stuber <stuber@loria.fr> (URL) (23 years ago, 29-Nov-01, to lugnet.robotics.rcx)
|
| |
| | Re: Output to Display
|
|
Alan (...) LCD (...) Yup. In RL2.5 Investigator, select through the palettes as follows: Datalogging & motors > RCX Communications > Set Display. The 'Set Display' icon looks like the RCX's LCD panel. You need to hang two modifiers off it. On the (...) (23 years ago, 29-Nov-01, to lugnet.robotics.rcx.robolab)
|
| |
| | Re: BricxCC release 3.3.2.12
|
|
(...) I guess I don't see so close a tie between the NQC code in a .NQC file and the brick type, port number, and program slot. A program running on RCX in slot 3 downloaded via COM4 could just as well run on an RCX2 in slot 1 downloaded via USB2. (...) (23 years ago, 29-Nov-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: BricxCC release 3.3.2.12
|
|
(...) In the simplest implementation (i.e., the one I'm likely to write) if you double click on an NQC file it will always open a new instance of BricxCC. That's the way it works right now. I may have it always bypass the "search" form when opening (...) (23 years ago, 29-Nov-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: BricxCC release 3.3.2.12
|
|
Hi John, I haven't installed the new version yet. Just a comment on my request. Your idea seems OK. However, this means you need two read two files. If I would have a look into my old.nqc file two months later I would see directly what settings (...) (23 years ago, 29-Nov-01, to lugnet.robotics.rcx.nqc)
|
