 | | Black
|
|
Since I am currently working on line following, I did some tests with the Lego active light sensor. I mounted one on a small test cart pointing down a bit more than 1/8 inch above the "ground". The 1.5 test pad reads white 57 black 38 green 46 I (...) (25 years ago, 28-Jan-00, to lugnet.robotics.rcx)
|
| |
| | Re: Curious problem with download
|
|
(...) Er, no I was thinking of the PCI cards that give up to 4 serial ports; KeySpan used to make them. They were a short PCI card with two or four serial ports, which used a custom extension to route SerialToolBox calls to the 'phantom' serial (...) (25 years ago, 28-Jan-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Curious problem with download
|
|
(...) I would have ascribed it to the USB to serial converter, but I also see this on the Sun with a real serial port. This is what makes me think it's a problem with my RCX or IR tower. Thanks, -Pete P.S. What you are thinking of is the stealth (...) (25 years ago, 28-Jan-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: legOS timers
|
|
(...) You nicer than msleep() and sleep()? --Ben (25 years ago, 28-Jan-00, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Curious problem with download
|
|
(...) downloading (...) I don't see any strange behaviour here; the hinky USB-to-serial interface is going to be your culprit. I had no problems using NQC on my PowerCenterPro (PowerComputing Macintosh clone) with a direct serial interface, but when (...) (25 years ago, 28-Jan-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Curious problem with download
|
|
I just got Mindstorm set, and since I do not have a PC, NQC seemed like a great place to start. I tried Mac NQC and did not get very far downloading the RCX firmware. Every attempt resulted in the IR tower not seeing the RCX. I have a G3 blue and (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: LegOS does not work on 1.5 RCX
|
|
Before anyone replies to my previous message, found the problem. I have a light over my desk and this was interfering with the IR transmission. Turned the light off and moved the RCX a little closer to the tower and hey presto, all OK. Does legOS (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
| |
| | LegOS does not work on 1.5 RCX
|
|
Hi I installed the win version of legOS and downloaded the firmware legOS.srec to both my RCX's. The older RCX from a 1.0 set seems to accept .lx files OK the first time after the firmware is downloaded. The new version will not accept any .lx (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
| |
| | more on the rotation sensor
|
|
I did some more experiments last night. My conclusion is that the majority of apparent 2-state transitions never actually occur (that is: the sensor does not actually travel through 2 states between two consecutive sensor readings). The order of the (...) (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
| |
| | legOS timers
|
|
Hi! Did anyone write any 'nicer' wrapper functions for handling the RCX timers? Or am I blind and can't find them? 8^) /Vlad (25 years ago, 27-Jan-00, to lugnet.robotics.rcx.legos)
|
