 | | Re: Using NXT Port 4 EIA-485
|
|
(...) Do you think it is possible to read/write binary and ascii data to this device or is there a special protocol neccessary ? What about bitrate of EIA-485 device ? Is it possible to adjust bitrate to anything more usable (9600, 38400, 115200) ? (...) (17 years ago, 9-Apr-07, to lugnet.robotics.nxt)
|
| |
| | Re: NXT external storage
|
|
(...) Yes, 9600 bits/s is really slow for storage access. Is there a known way to increase the clock and transferrate of I2C ? Christian (17 years ago, 9-Apr-07, to lugnet.robotics.nxt)
|
| |
| | Re: EggArt - a 4-colour Easter egg painting robot
|
|
(...) The promised videos (1-2Mb each): (URL) at 11Mb: (URL) David Schilling (17 years ago, 9-Apr-07, to lugnet.robotics.nxt)
|
| |
| | Re: Using NXT Port 4 EIA-485
|
|
(...) What is not supported about this port in the standard NXT firmware? You can read from it and write to it using the IOMapRead and IOMapWrite syscall functions. Looking at the firmware source code it certainly looks like everything is setup to (...) (17 years ago, 9-Apr-07, to lugnet.robotics.nxt)
|
| |
| | EggArt - a 4-colour Easter egg painting robot
|
|
Just in the nick of time, the day before Easter, I completed building a 4-colour NXT Easter egg painting robot. I started building it several months ago, when I thought I'd have plenty of time before Easter. Of course, at about the 85% complete (...) (17 years ago, 9-Apr-07, to lugnet.robotics.nxt, lugnet.org.us.smart) !
|
| |
| | RE: Using NXT Port 4 EIA-485
|
|
I've looked at implementing an interface for RobotC, but I've always struggled with why bother since there are no applications that connect to it. I wish LEGO had implemented an option to provide a logic level "RS-232" UART on port four. Yes, I (...) (17 years ago, 8-Apr-07, to lugnet.robotics.nxt, lugnet.robotics.nxt.nxthacking)
|
| |
| | Re: Using NXT Port 4 EIA-485
|
|
(...) As far as I know, there isn't any support for this interface in either the standard firmware or any of the other third party firmware implementations. The interface runs at 921,600 bps so it will be fast enough to be really useful. I am hoping (...) (17 years ago, 8-Apr-07, to lugnet.robotics.nxt)
|
| |
| | Re: NXT external storage
|
|
(...) It may work, but it will be very slow. The NXT runs the i2c ports at only 9600kb/s, so the data will trickle to the NXT very slowly. (...) I think that the answer is yes. (...) (17 years ago, 8-Apr-07, to lugnet.robotics.nxt)
|
| |
| | Re: NXT BrickSorter - Sorting bricks with a HiTechnic colour sensor.
|
|
(...) Thx for the comments. The design as it stands right now would not allow the sorter unit to rotate all the way around - not a bad idea though. I wanted to challenge myself with the angle idea on the sorter itself (2 rows of cups). With larger (...) (17 years ago, 8-Apr-07, to lugnet.robotics.nxt, FTX)
|
| |
| | Using NXT Port 4 EIA-485
|
|
Hi, is there currently any software-support (pbLua, NXT-G, NXJ) for NXT Port4 highspeed serial communication (EIA-485) ? This port can be used for connecting some new hardware (camera, SD-Card-storage) to the NXT... Thanks for more informations Bye (...) (17 years ago, 7-Apr-07, to lugnet.robotics.nxt)
|
