Subject:
|
Re: Short Circute Problem -- EMERGENCY
|
Newsgroups:
|
lugnet.robotics.handyboard
|
Date:
|
Wed, 7 Feb 2001 01:19:31 GMT
|
Viewed:
|
967 times
|
| |
|
|
Hi,
guys i realy in trouble now. i thought my memory fried out and replaced it with
new chip and quad nands(hc132). but still no luck. i ordered processor from B.G.Micro
and waiting for that shipment. do you guys have any idea what's the problem with my
board.
The battery led is not lighting up when board is operated only on battery. it is
lighting up once when i switch on the board and swhitching off then. i am still able
to load the Pcode succesfully. when i switch on the board lcd flickers and fades
away. IC won't sync with board. please help me. any ideas are welcom.
do you know somebody who can fix the board commercially.(is gleason research do
the repairs)
thank you very much.
Raju Kammela wrote:
> Hi guys ,
> i tried all the tests mentioned in the HB assembly to find out which
> part of the HB blown. No luck. i am giving the results here:
>
> 1) Tested the interface and charger board - looks good. (Both power supply and the
> MAX232 circuit)
> 2) Tested the Power supply for processor - good.
> 3) tested the clock freq of processor using voltmeter - good
> 4) tested the power for memory chip (U2) - good (in both on and off states)
> 5) Checked the bootstrap mode - good.
> 6) there is some problem with the battery led- when i switch on the HB it is
> supposed to be on (in case of no charger connected) but it is not consistent. some
> times it does , some times it is not. some times it flickers coupleof time. along
> with this
> led the motor indication LEDs also shitch on randomly every time i switch on the
> HB.
> 7) i am able to download the pcode. but when i reset the board by switching off and
> on still it displays the black boxes in the first line of LCD. LCD flickers and
> fades away some times.
>
> please help me with what should i do next. I am guessing memory chip is fried . but
> don't know how to test it. i need to test the processor too. no idea how to do
> that. the test i did in step 3 is only clock check right? it may not be meaning
> that 6811 is working properly... am i right? please help me with this. if i need
> to change these ics where can i get these?
>
> Thanks,
> Raj
>
> raju kammela wrote:
>
> > Hi Rainer,
> > thanks for your advise on this. i will fallow the test cycles
> > mentioned in HB
> > manual. What i noticed is , charging circuit(changeing/interface board) working
> > and
> > HB is working in bootstrap mode also. it is able to sync with IC in bootstrap
> > mode
> > and then i was able to download the Pcode. when i reset the board it is not
> > starting
> > working so. do you think it is the problem with processor? let me know if you
> > have
> > any hint about this. i will give you more details once i go through the
> > testing cycle in
> > HB manual.
> >
> > thank you very much for your help. i appreciate it.
> > Raj
> >
> > In lugnet.robotics.handyboard, Rainer Balzerowski writes:
> > > In lugnet.robotics.handyboard, Raju Kammela writes:
> > > > Hi Guys,
> > > > I got a serious problem with my HB. Bymistake my 12 volts 1 amp • power
> > > > cord touched to HB(which is on at that time) circut track near the HB's • direct
> > > > charge connector. then there is short circuit crisp sound from that are and • HB
> > > > stoped working. I switched off the HB and switched it on again. LCD is • showing
> > > > black boxes on the first line. Then i tried reloading the pcode. it is going
> > > > into boostrap mode and load was sucess. when i resetted the board it not
> > > > working again. i loaded pcode number of times still no use HB is not working.
> > > > every time i switch on HB one of the motor outputs or going high.
> > > > i thought only LCD is gone. but it is not, board is not responding
> > > > to IC except in bootstrap mode. so my question to you is where should i start
> > > > checking in the HB to find out which component is blown. do i need to change
> > > > the processor. please advise me......... any help in this matter is
> > > > appreciated.
> > > >
> > > > Thanks for your time,
> > > > Raj
> > >
> > > Hi Raj,
> > >
> > > first you should have a look at the assembly manual
> > > http://handyboard.com/hardware/assembly.html
> > >
> > > There are testing description for every step of assembling.
> > > So you'll possibly find the proplem on your own.
> > >
> > > If not you will have to describe the spot you touched your HB more precise .
> > >
> > > Did you mean charge connector on the little board from page11 from the manual • ?
> > > Then perhaps your bridge rectifier (AC-DC Converter ?) is gone with the wind,
> > > or the 5 Volts DC regulator or ...
> > >
> > > Look at their testing hints !
> > >
> > > Rainer
|
|
Message has 1 Reply:
 | | Re: Short Circute Problem -- EMERGENCY
|
| Raju, I have a handyboard version 1.21, on this board the battery led is working properly when it lights at power on and then goes off. According to the manual it should only remain lit when the power is too low indicating a dead battery. So I (...) (24 years ago, 12-Feb-01, to lugnet.robotics.handyboard)
|
Message is in Reply To:
| | Re: Short Circute Problem -- EMERGENCY
|
| Hi guys , i tried all the tests mentioned in the HB assembly to find out which part of the HB blown. No luck. i am giving the results here: 1) Tested the interface and charger board - looks good. (Both power supply and the MAX232 circuit) 2) Tested (...) (24 years ago, 2-Feb-01, to lugnet.robotics.handyboard)
|
6 Messages in This Thread:
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
