 | | Servo_a5
|
|
Hi, I'm using IC v3.1 beta 4. When I try to load the servo_a5.icb and the servo_a7.icb that I downloaded from the handyboard web page I get the following error: Fatal internal error: Illegal line in .s19 file And then it completely kicks out of IC. (...) (28 years ago, 12-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Pyroelectric Detectors
|
|
I'd like to incorporate a pryroelectric IR detector into my robot design. "Mobile Robots" has some detail on sensors, but I'd like to keep it cheap. I have an out-of-service Heath/Zenith motion detector lying about - is the sensor within similar to (...) (28 years ago, 12-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | R/C cars as robot chassis
|
|
Here is a rule of thumb to keep handy when converting R/C cars to robots; o If the R/C car used either NiCd batteries, or it had a NiCd battery pack, the motors will draw too much current for the Handyboard. This is strictly true of any controller (...) (28 years ago, 12-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Re: building a bot
|
|
From your post it seems that only one battery was used. It is best to have the motor(s) running from a separate battery. Apropriate capacitors for RF noise and large start up currents should be considered. Have fun! (...) Peter (...) ---...--- Ed (...) (28 years ago, 12-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Re: building a bot
|
|
Peter I tried to do modify a racer and found that the motors drew so much current that the board would continually reset. Another problem with the racers is that they are geared for high speed, not torque. I ended up making a circular frame and (...) (28 years ago, 12-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | building a bot
|
|
I seem to remember a while ago some person on this group was talking about making a robot from one of those tyco rc cars. Could I just plug the motors straight into the handy board and use the power supply from the inside of the car. Would a motor (...) (28 years ago, 11-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Used Handy Boards
|
|
Does anyone have a used HB? I would like a built one with a serial board too, it would have to work also. I could buy a complete kit with the serial board too. Any info would be great. I started using the board at school and would like to use one at (...) (28 years ago, 11-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Reset Button?
|
|
(...) This is a mistake, carried over from the 6.270 version of the document. thanks for pointing it out. -Fred (28 years ago, 11-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Re: User Buttons
|
|
(...) make sure you are loading "lib_hb.c" and not "lib_r22.c". -Fred (28 years ago, 11-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Re: (no subject)
|
|
(...) I'm pretty sure JDR microdevices carries the 1233. check (URL)2 > Since there are 16 address lines comming from the 6811. Could I use (...) The HB uses A15, along with the E clock and ~reset, as the enable line for the ram. The 64k address (...) (28 years ago, 10-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Re: buying miniboard
|
|
(...) I (CW Technology) still sell Miniboards. Check out (URL) for details. If you are looking for quantity, send me details and I can provide a quote. (...) The Miniboard doesn't have a "standard" set of sensors and battery. The Handyboard (...) (28 years ago, 10-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Reset Button?
|
|
In the Tech Ref, it refers to a "reset button". Where is it? (28 years ago, 10-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | (no subject)
|
|
hi all, I have a few questions. 1 > Does anyone know where I can get the voltage monitor, Dallas Semi 1233? 2 > Since there are 16 address lines comming from the 6811. Could I use a 64k Ram instead of a 32k? Is A15 being used for something else? (...) (28 years ago, 10-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | User Buttons
|
|
Why when I use this attached code, with the while(!start_button()) string does it tell me Function start_button undefined? -- Steve ___...___ * Steve Freedman * *For all your computer help, specializing in the Internet, the Mac* *OS, Windows 3.1, (...) (28 years ago, 10-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | buying miniboard
|
|
Does anyone sells miniboards? I'd like to order full kits including batteries and sensors. -Shay Shai Shomroni Science and Technology Education Center shaysh@post.tau.ac.il Tel-Aviv University, Israel (URL) fax:972-3-6407752 (28 years ago, 10-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | IR raw output
|
|
Hello all! I'd like to know if anybody ever tried to control a Nikon camcorder thru it's IR sensor. I think that the codes are Sony compatible, since I saw an identical camcorder, except that there was Sony trademark on it :). Anyway, I only want to (...) (28 years ago, 10-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Check out my new Robot page
|
|
Howdy, I just put up the first bit of the work in progress on my robot (named "GADGET"). The URL is (URL) I hope you will find it interesting! John Whitten (28 years ago, 10-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Re: IC memory error
|
|
The freeware version of IC runs in a virtual DOS box. Check your configuration settings to make sure you give the maximal amount of conventional (640K) memory to the DOS box. Also, try using the .pif file that is distributed with IC. -Fred In your (...) (28 years ago, 9-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | IC
|
|
hi everybody, i was not sure if this reached the net before....so iam posting it again whenever i download a program from the prompt to the handyboard, the following message is displayed.... " IC is running dangerously low on memory. Your PC shpuld (...) (28 years ago, 9-Nov-96, to lugnet.robotics.handyboard)
|
| |
| | Re: "Mobile Robots: Inspiration to Implementation" for FIVE BUCKS!!
|
|
(...) No. I got my book in about a week, and the invoice has no phone or more complete address than shown above. They do not accept phone orders or credit cards. (28 years ago, 9-Nov-96, to lugnet.robotics.handyboard)
|
