 | | Re: Short Circute Problem -- EMERGENCY
|
|
Hi, guys i realy in trouble now. i thought my memory fried out and replaced it with new chip and quad nands(hc132). but still no luck. i ordered processor from B.G.Micro and waiting for that shipment. do you guys have any idea what's the problem (...) (26 years ago, 7-Feb-01, to lugnet.robotics.handyboard)
|
| |
| | Equivalent/Compatible sensor to Sharp IS1U60
|
|
Hi All, I was wondering if there was a another sensor compatible with the handy board that i could use in place of the Sharp IS1U60 IR demodulator, that is more readily avalable (ie in Radio Shack etc), to recieve signals from a Sony remote control (...) (26 years ago, 7-Feb-01, to lugnet.robotics.handyboard)
|
| |
| | where is ldxibase.asm
|
|
Hi, I am doing some assembly programming for the Handyboard and I can't seem to locate the file ldxibase.asm used in many of the .asm examples I have seen posted on the Handyboard site. Any idea where I can get it? Or tips on creating it. Also, I (...) (26 years ago, 6-Feb-01, to lugnet.robotics.handyboard)
|
| |
| | Re: IC problem
|
|
Fred and Jim, Thank you for your quick responses. I can now see that I was trying to make a relatively simple piece of code very complicated. I rewrote the program using Fred's suggestions and wound up with the following simple, efficient program (...) (26 years ago, 5-Feb-01, to lugnet.robotics.handyboard)
|
| |
| | Re: IC problem
|
|
Hi. The default process is running of out stack. This is because you've written a program in which one function calls another, which calls another, which calls the first. Each time a function is called, an internal "call stack" must keep track of (...) (26 years ago, 4-Feb-01, to lugnet.robotics.handyboard)
|
| |
| | IC problem
|
|
I have written a small program for the Handyboard to test program flow in IC. It is supposed to print "Step1", "Step2", Step3" in sucession to the LCD in an endless loop until I reset the board. It works properly through 12 cycles but on the 13th (...) (26 years ago, 4-Feb-01, to lugnet.robotics.handyboard)
|
| |
| | Re: Short Circute Problem -- EMERGENCY
|
|
Hi guys , i tried all the tests mentioned in the HB assembly to find out which part of the HB blown. No luck. i am giving the results here: 1) Tested the interface and charger board - looks good. (Both power supply and the MAX232 circuit) 2) Tested (...) (26 years ago, 2-Feb-01, to lugnet.robotics.handyboard)
|
| |
| | RE: 68HC11 (Evaluation Board)
|
|
I was wondering if anyone was aware of any pre-existing library calls that would allow an individual using an Evaluation Board (EVB-68HC11)+ Buffallo Monitor(ImageCraft C v5.0) to access the system clock. I've noticed that with using Interactive C (...) (26 years ago, 1-Feb-01, to lugnet.robotics.handyboard)
|
| |
| | unsuscribe
|
|
How do i unsuscribe from the list? Thank you. (26 years ago, 1-Feb-01, to lugnet.robotics.handyboard)
|
| |
| | Re: Short Circute Problem -- EMERGENCY
|
|
Hi Rainer, thanks for your advise on this. i will fallow the test cycles mentioned in HB manual. What i noticed is , charging circuit(changeing/interface board) working and HB is working in bootstrap mode also. it is able to sync with IC in (...) (26 years ago, 1-Feb-01, to lugnet.robotics.handyboard)
|
