 | | Re: Miniboard download random failures
|
|
(...) "expected (...) James, Yes, I am running from a DOS window in W9X. Do I have to boot to DOS mode to correct for this? Uhm, I'm a Mac person, so, have patience, how does one boot to DOS instead of Win95? thanks, DLC (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Miniboard download random failures
|
|
(...) Are you running DLM from a dos window in Win9x? I've had this problem but it usually stops when I run it in DOS. Just a thought. -Jim Munro <jimmn@xnet.com> (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Freeware ICC11 and bad iasm11.exe?
|
|
Me again, I just got the ICC11 freeware from the Miniboard site and installed it, moving the crt.s over as it says to do in the docs, etc. I tried to compile the test compile of icc11 dhry.c printf.c and got a LOT of "phasing" errors, whatever that (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Miniboard download random failures
|
|
Hello, I just finished building a Miniboard using the HC811E2 processor. After swapping the Rx and Tx lines on my serial cable the download and reset switch do as the manual says. However, when I use dlm to download a program the bootstrap section (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | serial communication
|
|
Hi.. I am also facing problem in serial communications. My problem is that I am trying to use the handyboard to drive a modem. I have used a cross-serial cable to connect my handyboard's external serial board to a modem. But whenever I run my app, (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | R: communication via serial port
|
|
Using java and comm API ? ----- Original Message ----- From: Ray Tang <raytang_1@hotmail.com> To: <handyboard@media.mit.edu> Sent: Thursday, October 05, 2000 4:49 AM Subject: communication via serial port (...) and (...) the (...) a (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Linux and v1.21 handyboard (fwd)
|
|
Hi, I've successfully located and compiled the IC files for the Handy Board. I can load and run programs on the board, BUT the digital input(s) are not being "seen". E.g. a simple program like: void test3(){ while (1){ if (digital(10)) printf("10 is (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | communication via serial port
|
|
Hi, This isn't an off topic question... Has anyone tried programming the serial port (on Linux) to communicate with the Handyboard? I am working on an RF link between the Handyboard and a PC via serial communication, but I don't know much about (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Re: external power
|
|
I am by no means an expert on the subject but this is how I did it. First I cut the heavy motor power trace as shown in the FAQ. Next I soldered a four pin female header on top of the expansion board where the expansion board picks up power for the (...) (24 years ago, 4-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Multiple GP2D02 range sensors
|
|
Greetings, (...) From what I could understand from the documentation ((URL) you could use one timing signal for all of them, as long as each sensor is connected to its own output line (to which the sensor would serially output its 8 bit value). (...) (24 years ago, 4-Oct-00, to lugnet.robotics.handyboard)
|
