 | | Capacitor on Sonar Board
|
|
The instructions on connecting the Polaroid Ultrasonic Ranging System to the Handy Board (at (URL) say to be sure and install the 0.1 uF capacitor in the C7 position on the sonar board. It is unclear what is meant here. Is this refering to the (...) (24 years ago, 26-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Out of Office AutoReply: robot contest
|
|
I'm out of the office starting Mon, 9/25, returning Thurs., 9/28. Call Mike Kaphon 11325 with urgent matters. Thanks. (24 years ago, 25-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | robot contest
|
|
Ever wanted to join a robot contest? No events in your area? Give your robot a try at F.IRC. Join the First Internet Robot Contest (F.IRC) for robotics hobbyists around the world. No entrance fee! DATE: Oct 1 – Nov 30 (URL) 20+ attractive prizes: (...) (24 years ago, 25-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Batteries again, sorry
|
|
you're almost right. if you plugged a nimh pack into the HB's charge jack, the external pack would charge the internal batteries. but it would not power the board significantly. this is because the HB's charge jack includes a current-limit resistor (...) (24 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Batteries again, sorry
|
|
This should be my last question in terms of batteries. Assuming that I have nicads powering the HB, what effect would there be if, when the batteries were getting low, I connected a fully charged battery pack (e.g. containing the nimh cells) into (...) (24 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Batteries again
|
|
in theory this can be a problem. in practice, as long as the nicads are occasionally allowed to fully discharge, they'll last for a good long time in fine condition. fred In your message you said: (...) es. (...) (24 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Batteries again
|
|
As Fred is recommending using nicads due to the constant trickle charge when connected to the mains adapter I have a question regarding the nicad batteries. If the batteries are trickle charged before they are fully discharged (usual practice I (...) (24 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Possible error in assembly guide.
|
|
Are you getting a good ground???...??? If it works.. then hey! RS232 is +10 to -10 but there is room for slop! +7 to -7 will work too!!!!!!! It just won't drive a cable to the max length of the RS232 spec. Most of the time though people just don't (...) (24 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Possible error in assembly guide.
|
|
Near the end of the "interface/charger serial circuit" heading of the "Assembling The Handy Board" guide, it says measure the voltage of pin 6 of the MAX232, I did that and got -9.5 which is correct. Then I connected pin2 of j9 and pin6 of max232 so (...) (24 years ago, 22-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Re: nimh batteries
|
|
the issue with nimh is that plain trickle charge is not appropriate. you must remove charge current when the cells are full charge. the HB charge circuit just doesn't do that. i'd really recommend switching back to nicad. fred In your message you (...) (24 years ago, 21-Sep-00, to lugnet.robotics.handyboard)
|
