 | | RE: Newton Labs Not releasing PCODE source for 3.1
|
|
Jerry- You didn't 'buy' IC 3.1. You paid for a license to use the software. I doubt that you were buying the actual source code, which probably took hundreds of hours for the programmers to write. That is their intellectual property, and it is their (...) (24 years ago, 6-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Any SPI bus gurus out there?
|
|
Hi, I have a question. Does the sonar implementation that's suggested prohibit you from adding additional devices to the SPI bus? I know you can add as many SPI devices as you have enable lines. I'd like to add sonar, compass, and RTC / battery (...) (24 years ago, 6-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Newton Labs Not releasing PCODE source for 3.1 -> Fred Help!
|
|
George Musser brought up a very good issue! Where the heck is pcode_hb.asm? This code was released in ver 2.86 and enhancements were made to the pcode from the user base. Newton Labs has tunnel vision and NO CLUE to how open source software can (...) (24 years ago, 6-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Pcode source code; disabling the LCD
|
|
Hi all, Does anyone have a copy of the pcode source for IC 3.1? According to an earlier posting, it used to be available on the Newton Labs FTP site, but it's not there anymore. Also, has anyone ever completely disabled their LCD? Even after the (...) (24 years ago, 4-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Here's the Rover with handyboard
|
|
Hello Jerry, Did not get the picture of the Mars Rover. Sounds like you have a good start on your robot, please keep us advised on the problems and solutions. Was it hard to convert the mice encoders?? should be very accurate, please post the (...) (24 years ago, 4-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Here's the Rover with handyboard
|
|
Attatched is a picture od the toy Mars Rover that I am modifying. Right now I have the handyboard driving two lego motors and I ripped apart a mouse to use the encoder. Mice encoders sure work great! And they are much cheaper than commercial (...) (24 years ago, 3-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Linux Works well with the handyboard! and Cool Platform Hack!
|
|
Hi, I got all the bugs out of my handyboard! First I had to bend several leafs on my 68HC11 (Thanks Fred!), Socket was ok, the processor was not. Also, when I did a burn in of my board, I did a complete trickle charge on the battery pack, ran (...) (24 years ago, 2-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Temporary solution for W2000, but not Notebook
|
|
Hi, I am assisting a Robotics course with the venerable HandyBoard, and have been having the same problem with the Toshiba, and ThinkPad laptops. With Toshiba though, there is no infrared as far as I can tell, and I can run and load the inital pcode (...) (24 years ago, 1-Sep-00, to lugnet.robotics.handyboard)
|
| |
| | Servo.c
|
|
Hi. I´m using the servo_a7.icb file to drive a servo on my handyboard, but the servo is not moving. it seems that the frequentcy is not the right one (40hz). And I was looking for the servo.c file, because it seem easy to use, but i can´t find it. (...) (24 years ago, 30-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Hi all
|
|
Dear Everyone, Nicolle and Jason have split up. The hoovjay@saber.net email account will end today. To email Nicolle use: hoover@math.ucdavis.edu To email Jason use: jtparks@flashcom.net I hope everyone is doing well, Jason (24 years ago, 31-Aug-00, to lugnet.robotics.handyboard)
|
