 | | Temporary solution for W2000, but not Notebook
|
|
This is essentially a status report telling what I've come up with as a partial solution to to running the Handy Board in our new environment. I have not succeeded in getting IC to run under Windows2000 DOS. The labs now have machines with 120 MB (...) (24 years ago, 31-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | IR demodulator
|
|
I have mounted the IS1U60 infrared demodulator on to the HB but I have realised that it can only recieve from a particular direction. Is it possible to mount another IS1U60 by connecting the leads to the same locations on the pcb via wires and then (...) (24 years ago, 29-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Is this a bad PLC socket?
|
|
Hi, I built up a handyboard and most of it works great! testmotor passes, testdigitals passes, even the infrared remote detects and trnasmitts fine! I just have one analog port, port 3 that does not work unless I apply a little pressure to the cpu! (...) (24 years ago, 29-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Lego RCX rotation sensor w/handyboard
|
|
(...) The Expansion Board has inputs specifically for Lego sensors. In particular, I've used the rotation sensor and it works fine. You simply take a lego connector, cut the wire and put the HandyBoard connector on. Plug it in and you're ready to (...) (24 years ago, 26-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Re: IR output driver
|
|
it's rated for 1 amp. so you'd have no trouble at all with what you describe below. fred In your message you said: (...) (24 years ago, 26-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Lego RCX rotation sensor w/handyboard
|
|
Hello, With the Handyboard expansion board, you will connect the LEGO rotation sensor (LEGO Angle sensor) easily. Here is the link: (URL) Hui (URL) Message----- From: Andrew McGeachie <geech-lugnet-news@engine5.com> To: handyboard@media.mit.edu (...) (24 years ago, 25-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Lego RCX rotation sensor w/handyboard
|
|
apologies if this is a frequently asked question...i'm a newbie to this list. is it possible to hook up a Lego Mindstorms rotation sensor to the handyboard? and if so, does anybody have good instructions for doing it? thanks. - andrew (24 years ago, 25-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | RE: IR output driver
|
|
Hi! Zetex has a great tech page where all of the specs are listed: www.zetex.com It will have the beta values... Kent | -----Original Message----- | From: jhatton@media.mit.edu [mailto:jhatton@medi...mit.edu]On Behalf Of | John Hatton | Sent: (...) (24 years ago, 24-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Fuzzy Logic
|
|
Does any body know where I could find code, to run fuzzy logic on a HC11? Thanks Daniel (24 years ago, 22-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Remote controlled robots with handy board?
|
|
Hi Jack, You can check with the following site for radio communication for Handyboard: (URL) you want to know more "Handyboard" based robot and applications, you can check: (URL) Regards, Patrick Hui patrick@robotstorehk.com -----Original (...) (24 years ago, 24-Aug-00, to lugnet.robotics.handyboard)
|
