 | | IR demodulator
|
|
I have mounted the IS1U60 infrared demodulator on to the HB but I have realised that it can only recieve from a particular direction. Is it possible to mount another IS1U60 by connecting the leads to the same locations on the pcb via wires and then (...) (26 years ago, 29-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Is this a bad PLC socket?
|
|
Hi, I built up a handyboard and most of it works great! testmotor passes, testdigitals passes, even the infrared remote detects and trnasmitts fine! I just have one analog port, port 3 that does not work unless I apply a little pressure to the cpu! (...) (26 years ago, 29-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Lego RCX rotation sensor w/handyboard
|
|
(...) The Expansion Board has inputs specifically for Lego sensors. In particular, I've used the rotation sensor and it works fine. You simply take a lego connector, cut the wire and put the HandyBoard connector on. Plug it in and you're ready to (...) (26 years ago, 26-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Re: IR output driver
|
|
it's rated for 1 amp. so you'd have no trouble at all with what you describe below. fred In your message you said: (...) (26 years ago, 26-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Lego RCX rotation sensor w/handyboard
|
|
Hello, With the Handyboard expansion board, you will connect the LEGO rotation sensor (LEGO Angle sensor) easily. Here is the link: (URL) Hui (URL) Message----- From: Andrew McGeachie <geech-lugnet-news@engine5.com> To: handyboard@media.mit.edu (...) (26 years ago, 25-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Lego RCX rotation sensor w/handyboard
|
|
apologies if this is a frequently asked question...i'm a newbie to this list. is it possible to hook up a Lego Mindstorms rotation sensor to the handyboard? and if so, does anybody have good instructions for doing it? thanks. - andrew (26 years ago, 25-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | RE: IR output driver
|
|
Hi! Zetex has a great tech page where all of the specs are listed: www.zetex.com It will have the beta values... Kent | -----Original Message----- | From: jhatton@media.mit.edu [mailto:jhatton@medi...mit.edu]On Behalf Of | John Hatton | Sent: (...) (26 years ago, 24-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Fuzzy Logic
|
|
Does any body know where I could find code, to run fuzzy logic on a HC11? Thanks Daniel (26 years ago, 22-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Remote controlled robots with handy board?
|
|
Hi Jack, You can check with the following site for radio communication for Handyboard: (URL) you want to know more "Handyboard" based robot and applications, you can check: (URL) Regards, Patrick Hui patrick@robotstorehk.com -----Original (...) (26 years ago, 24-Aug-00, to lugnet.robotics.handyboard)
|
| |
| | Remote controlled robots with handy board?
|
|
Hi, I was wanting to create a robot that has controlled though a wireless remote controll type of device, is this possiable with the handyboard or an extrenel device (for communications) that feeds the hand board the information? Would the (...) (26 years ago, 24-Aug-00, to lugnet.robotics.handyboard)
|
