 | | Re: 6.8nF Capacitor
|
|
I don't suppose you know what the formula is for calculating the value of the frequency ?. 1/(R4*C6) possibly ?. This equation gives 38396Hz (38.4KHz) which means that my 6.6nF caps give 39560Hz (39.6KHz) which is closer to 40KHz than the 6.8nF (...) (26 years ago, 12-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Robot positioning
|
|
Hi Kate, I just want to know how/where to get a sonar transmitter/reciever pair with different frequencies for robot positioning. Can sonar module from Polaroid do that? Thanks, William (...) on (...) (26 years ago, 12-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Robot positioning
|
|
If you want to return to "base," all you need is a beacon of some sort. For example, you could use CdS cells (or anything that finds EM in the visible light/low IR range) and a lightbulb (or series of lightbulbs, like a strand of Christms tree (...) (26 years ago, 11-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Melissa Virus
|
|
I have found the source and fortunately it is not from a HB site. It was from the Washington and Lee University EE school. (26 years ago, 11-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Robot positioning
|
|
Hello all, I am currently building a H board/exp board based robot that has (will have) the following sensors: Diffrential drive wheel encoders, hamamatsu sensors combined with the software from the H board site for motor control and distance counts (...) (26 years ago, 11-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Follow-up to Virus
|
|
It is amazing what can be recovered off a disk, with the right tools. This is the data on the virus files. The document, final1r....doc, within the zip file 478eti.zip is the culprit. "This file was quarantined.f M The file (...) (26 years ago, 11-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | File Contains Virus
|
|
There is a file located on one of the HB sites that contains the Melissa W97 virus. It begins with 478... I am sorry that I can not give you more info as the virus scanning software removed the file, but if you maintain a server with HB files on it, (...) (26 years ago, 11-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Re: four polariod sonars
|
|
Hi, I read the design a while back... Don't you just control the multiplexor circuit on the handyboard and then call the sonar routines? All sonar use the same routine, aren't they? -- Ray JULIAN REYES <handyboard@media.mit.edu> wrote in message (...) (26 years ago, 11-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard startup problems
|
|
Yes, I encounter something similar. Do you use servo on your board? I also have some trouble with the motor ports. I am not sure what causes it. I also have trouble with the motor ports. When I run the motor at 50% power (back or forward), both red (...) (26 years ago, 10-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | H2000 optical position sensor
|
|
Hi, I am planning to build a position detector with a H2000 chip. The chip is used in several optical mice, for example the H2000/0006 can be found inside the Microsoft IntelliEye mouse. I sill have difficulties in finding the manufacturer and the (...) (26 years ago, 10-Jul-00, to lugnet.robotics.handyboard)
|
