 | | (no subject)
|
|
hola: estoy muy interesada en saber como puedo comunicarme por el puerto serial a partir del microcontrolador 68hc12 de motorola. les agradeceria se me pueden enviar toda la informacion al respecto. gracias por su atencion. (24 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Reset on the HB
|
|
Could someone tell me where the reset button refered to in documents for the Handy Board is? I know the master reset is the on/off switch. TIA. Steve (24 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Re: 6.8 nF Capacitor
|
|
The 6.6nF was the capacitance measured for the two 6.8nF capacitors that I have managed to get (rated as 10% tolerance). The problem is that the parts listed for the HB are 2% tolerance 6.8nF capacitors which gives a lowest value of 6.6664nF which (...) (24 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Re: 6.8 nF Capacitor
|
|
(...) Yes. Capacitors have typically very loose tolerances anyhow; usually 20% unless you buy specifically selected samples in a tighter tolerance. The 6.8 is a standard value while the 6.6 you have is likely a specially selected non-standard value. (...) (24 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | 6.8 nF Capacitor
|
|
Can any body tell me if a 6.6nF capacitor will do to replace the 6.8nF in the IR Transmission circuit (Fred?) ?. Thanks in advance. John Hatton (24 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | HB to Comms board cable
|
|
Is there a 'best' length for the telephone cable between the HB and the Comms board. I am about to start construction and I was wondering if there was a maximum length for the cable and if a particular length was recommended. Thanks for your help. (...) (24 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Connect HP 48GX
|
|
Gruezi/ Hi, (...) Instead of using the serial port, how about using the HP4**x IR port? I recall there being HP4**x programs that emulate IR remote controls which should be easy to modify (?) for general-purpose communications. Marco A. Assfalk de (...) (24 years ago, 6-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Handyboard startup problems
|
|
Hi all, I'm having some problems with me previously functioning handyboard. I'm using a standard board which has worked fine for nearly a year. Recently it didn't get any use for awhile and the batteries ran down. After charging them for 18+ hours I (...) (24 years ago, 5-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Re: 6.8nF Capacitor
|
|
(...) Not knowing what parts the HB uses, but assuming it is something like a polystyrene cap, then I think I have some in my component drawer. Send me your address, and I'll stick a couple in the post. Best Wishes (24 years ago, 5-Jul-00, to lugnet.robotics.handyboard)
|
| |
| | Re: VECTOR 2X
|
|
This is my routine to use the Vector 2x with my board (see link below my name) with an I/O expansion board connected. You will need to change the I/O port #defines to work with the Handy Board I/O ports on your expansion board, but other than that (...) (24 years ago, 4-Jul-00, to lugnet.robotics.handyboard)
|
