 | | ICn for a Mac?
|
|
Has anyone ported Kurt Konolige's ICn compiler to the Mac or MSDOS? Thanks! George Musser georgejr@musser.com (24 years ago, 25-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Re: RCX vs. HandyBoard
|
|
(...) Here's one I can answer, at least a little bit: There's an HC11 port to gcc-2.8.1 and a Handyboard library to go with it. There's also a GCC-2.9.5 version out there. (URL) get you to either one. I program my Handyboard using Linux and GCC (...) (24 years ago, 25-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Re: RCX vs. HandyBoard
|
|
(...) Here's one I can answer, at least a little bit: There's an HC11 port to gcc-2.8.1 and a Handyboard library to go with it. There's also a GCC-2.9.5 version out there. (URL) get you to either one. I program my Handyboard using Linux and GCC (...) (24 years ago, 24-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | driving servos by the handy board!
|
|
Dear Sir, I am a new user of the handyboard. In a robot project of building a manipulator, I have to drive for at least 3 servo motors. I have found the routines for driving two servo motors at the same time from the handyboard info website. But, if (...) (24 years ago, 23-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Re: RCX vs. HandyBoard
|
|
Here are some more specific questions that I still have: 1) Can two handyboards communicate with each other from a distance?, either in the same room (i.e. infrared) or via the internet? 2) Besides Interactive C, what exactly are the other ways that (...) (24 years ago, 23-Apr-00, to lugnet.robotics.handyboard, lugnet.robotics.rcx)
|
| |
| | Servo function (new?)
|
|
Hello all, here's a servo function that I worked up. It's really very simple, but I figured that someone else might want to use/hack it up. My problem was that I wanted to be able to set the servo (non-continuous) at *any* point in its travel (...) (24 years ago, 23-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | IR communication power
|
|
Hi everyone, I am now trying to use the IR transmitter and receiver to communicate two HB. The method seems work, but the main problem is the transmitter power is seems too weak. My HBs can only communicate within a few inches. My question is: Is (...) (24 years ago, 22-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | wits end with PWM measurement
|
|
Dear All I'm at my wits end on this one. It's a little routine to measure on PA0 a pulse width of a PWM signal generated on PA7. The two pins are linked with a jumper. I've looked through all the books and and handyboard archive, but all I get is (...) (24 years ago, 22-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Re: RCX vs. HandyBoard
|
|
the HB FAQ has some of this. there is a listing of the specific features of the HB. see (URL) your message you said: (...) e (...) t (...) n (...) (24 years ago, 22-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | RCX vs. HandyBoard
|
|
is there a website that gives a side-by-side comparison of the features of the handyboard vs. the RCX? i'm giving a series of talks to professors about the rcx and robolab, and some of them have asked about the handyboard, but i don't know a whole (...) (24 years ago, 22-Apr-00, to lugnet.robotics.handyboard)
|
