 | | 5V of trouble
|
|
i'm assembling the handyboard according to the instructions found on the HB site. When measuring the E clock signal using a voltmeter, i register 5V instead to the anticipated 2.5V. i've re-checked all the solder joints but there doesn't appear to (...) (25 years ago, 6-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Output to file option for IC?
|
|
(...) Here's a stupid idea, but might be the simplest: Run a dumb terminal program. I keep a very old version of Telix for DOS around for this purpose. Most of the dumb terminal programs have some option or other for logging or capturing to a file. (...) (25 years ago, 6-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Motor Drivers
|
|
(...) As others have said, the system should be able to drive this. However there are some obvious 'thoughts': 1) A light that draws 300mA when running, will _momentarily_ draw a much higher value when the bulb is cold. The actual ratio between the (...) (25 years ago, 6-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Output to file option for IC?
|
|
We have a system that was designed to let you run IC-like code on a host as if it were running on the HB. We use the HB as an extension to a larger mobile robot (the HB turns on lights, motors, etc. Our robot served candy via voice command at last (...) (25 years ago, 6-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Output to file option for IC?
|
|
It would be cool if IC can output results to a file. well, since it can't does anyone have code available for borland c++ which will receive data over the serial port? I found some code from earlier posts, but can't seem to find one that works. I (...) (25 years ago, 6-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Motor Drivers
|
|
300 mA shouldn't be a problem. are your main batteries low? alternately, are you sure it's 300 mA at 9v? can you measure it somehow. fred In your message you said: (...) (25 years ago, 6-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Motor Drivers
|
|
I am trying to run a light with the motor outputs on the handy board. I looked up the spec on the L293D and it claims to be capable of 600mA constant and 1.2A peak. The miniature light I am using draws about 300mA. When the light comes on the handy (...) (25 years ago, 6-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Re: sonar mapping with evidence grid
|
|
(...) home (...) I have read that it is not actually a solid cone angle, but a peak central lobe and a few side lobes. I think the best way to figure this out is to mount your sonar sensor on a rotatable head and go out to an open field. Place a (...) (25 years ago, 5-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | Re: LED's
|
|
[Derek Healy] spake unto the ether: (...) This is just an idea skeleton, but not too hard to flesh out, if you've worked with TTL. The Handy Board memory map maps some upper 32K addresses to I/O "ports". Look at the schematic and you can see which (...) (25 years ago, 5-Apr-00, to lugnet.robotics.handyboard)
|
| |
| | LED's
|
|
Hi, could anyone tell me how I might light LED's in sequence so that they would simulate a rev counter of an automobile & to also simulate the speed counter. I need to know how I might wire them up and how I might be able to program them using time (...) (25 years ago, 5-Apr-00, to lugnet.robotics.handyboard)
|
