 | | Re: Hitachi LM052-L
|
|
Jan, Do you have the expansion board? If so, have you tried removing it and seeing if the display works on the Handy Board by itself? What makes you think the display is damaged? What are the symptoms? Does IC still work, even though the display is (...) (25 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Hitachi LM052-L
|
|
Hello, my Hitachi LM052-L display is damaged. Does anybody know where to buy a new one or equivalent in Europe ? Or how to test which part is damaged of the handyboard display system or the display itself ? Thank You ! Jan Luijk Netherlands (25 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Q: 10 dc motors on handyboard?
|
|
Does anyone know if handyboard can run more than four dc-motors? I want to be able to control a complex lego construction, with full control of all motors at once. The current flow shouldn't be to dramatic, I hope. I would also like to ask how it is (...) (25 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharged battery?
|
|
hi dennis, well, it's just a plain C/10 charge circuit. but i was under the impression that nicad's aren't damaged by that. it's possible i'm wrong :-). any other battery experts out there? fred In your message you said: (...) ly (...) ut (...) (25 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharged battery?
|
|
(...) I was guessing here - most chargers don't check for peak charge, since I didn't know if the Handiboard charger did or didn't... If the charger has a trickle charge of more than C/50 or C/100 then NiCds will be damaged eventually on a long-term (...) (25 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Vector 2X driver
|
|
I just bought a Vector 2X electronic compass for a project. In looking at it the manual, I see that if the 2X is run in slave mode I can clock out data from it at my leisure using any digital pins available on the Handy Board. This could almost be (...) (25 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharged battery?
|
|
no i disagree with this answer. the HB is designed to be left on normal charge indefinitely. the batts can get a little warm. if they are hot then something is wrong, but a little warm is nothing to worry about. when fully charged and with no load (...) (25 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Non-polaroid Sonar
|
|
In the sonar code from the web site, the rising edge detection on timer input channel 3 (TIC3) is set like this: bit_clear( 0x1021, 2 ); bit_set( 0x1021, 1 ); According to the little pink book, address 0x1021 is the Timer Control Register 2 (TCTL2) (...) (25 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharged battery?
|
|
(...) Ouch. You don't want to do that too much or you will torch (may have torched) your NiCds. NiCds do NOT like to be overcharged, it causes a problem called Voltage depression that many mistakenly call "memory effect". [snip] (...) Servos will (...) (25 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Overcharged battery?
|
|
actually this is to be expected. with no load, the diodes produce no drop. if you're worried, try hooking a DC motor (or other real load -- light bulb, 10 ohm resistor, etc). across the servo motor supply and then measure the voltage. you should see (...) (25 years ago, 15-Mar-00, to lugnet.robotics.handyboard)
|
