 | | Your site has been included on OpenHere
|
|
Hi, Your site has been included in the OpenHere.com index and search engine. OpenHere is one of the 10 largest index and search sites on the Internet. Your site listing is: Link: (URL) The Handy Board Description: The Handy Board is a 6811-based (...) (25 years ago, 22-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard C library for m6811 gcc port
|
|
Curt Mills, WE7U writes: > I was going to get to modifying it for Stephane's port, but haven't > gotten around to it. Thanks! I knew about this library, but I was hoping to prod some other porters to the surface with my comment. I guess I'll be (...) (25 years ago, 21-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Modifying a servo for use with HB
|
|
(...) What sources for servo hacking have you read? Depending on the servo (the Futaba S148 is the easiest), there are a few things to do. Using the 148 as my example; Clip off the end-stop and pull the bushing from the spline gear and remove the (...) (25 years ago, 21-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Handyboard and MIDI
|
|
I'm trying to use my handyboard to send MIDI messages to a host. I downloaded and tried the MIDI libraries from Colby Leider, and it looks like it's just what I need, but I can't get them to work with IC 2.8. Is anyone using the Handyboard with (...) (25 years ago, 21-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Hewlett Packard optical encoder
|
|
Hi, Since photo reflector with segmented wheel pattern doesn't help in precise mobile robot navigation, I intend to use Hewlett Packard optical encoder and I have selected HEDS-9140 series.I know someone has tried this item long time ago and I hope (...) (25 years ago, 21-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Modifying a servo for use with HB
|
|
If you just want to use them as motors, then B is the appropriate solution. You are correct in the motor PWM routines are just used to control the amount of energy going to the motors. The servo routines (using the expansion board) are the kind for (...) (25 years ago, 21-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Modifying a servo for use with HB
|
|
When connecting my servos (now gear head motors) to the HandyBoard - do I need to a) replace the pot with the resistor network or b) remove the electronics all together? I'm unclear if the PWM routines on the HB (fd, bk, and motor) are the kind of (...) (25 years ago, 21-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | multitasking support.
|
|
i'm running IC version 2.82. i'm not too sure how do i get the handyboard to do multi tasking on three routines: 1. control the velocity of the robot (i called the function 'dc') 2. steer (i'm steering with a front wheel) 3.identify strips on the (...) (25 years ago, 20-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Shaft encoder
|
|
I'm using a slot sensor (break beam) as part of my shaft encoding. the slot sensor is reading the number of breaks when the 6 spokes (attached to the shaft) spins. i'm using the Sencdr1.icb file to do drive the shaft encoder. i notice that there (...) (25 years ago, 20-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: AOL Instant Messenger
|
|
This is a SCAM ~ intended to get your password this isnt a valid AOL website ~ BE WARE of SPAMMERS (25 years ago, 20-Jan-00, to lugnet.robotics.handyboard)
|
