 | | Attaching a servo to a Rug Warrior Pro
|
|
Ok - I'm a newbie! But I'm really hoping the collective wisdom of this newsgroup will be able to help me with extending the abilities of the Rug Warrior Pro I've been working with for the past 2 months. I've recently purchased and connected three (...) (25 years ago, 18-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Refresh-rate of GP2D12
|
|
(...) (25 years ago, 18-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Refresh-rate of GP2D12
|
|
Hi, there is a new datasheet available for Sharps GP2D12-device. The refresh rate is definetely worse than 32ms as posted before, the correct (worst case) value is about 53 ms. See: (URL) for details DIRK (25 years ago, 18-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Robotics Show on TLC
|
|
(...) Thank you for this pointer. I taped it (locally it was at 2am Sunday!) and we found it very interesting. I especially like the wheel design behind the JPL Nanorover ((2 URLs) (25 years ago, 17-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | How to connect handy board with linux
|
|
Hi, I have a problem, I wish someone can help me. I use linux to control my handy board. I can type command under IC, but I can do nothing without IC. HOw can I do something out of IC? Like type some command in another terminal? Your help will be (...) (25 years ago, 17-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Can't get input capture to work
|
|
I'm hoping someone can help me figure out the problem with the following driver. Ultimately I want to simulate a sony IR remote control using a 6.270 board. I acquired the sony-ir.asm and tried it out, but that wasn't working; so I trimmed it down (...) (25 years ago, 17-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Lego-izing the Handyboard.
|
|
Mark -- I built a chassis for my robot that cradles the HB and clamps two Lego gear motors solidly in place. Check out this web page for photos: (URL) side of the chassis consists of two sixteen-unit beams, one on top of the other with two-unit (...) (25 years ago, 17-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Lego-izing the Handyboard.
|
|
I've mentioned this subject before here, but I never really got an answer that made much sense... Has anybody ever tried building a reasonable "LEGO-ish" container for the Handyboard? Ideally, that would be a sturdy enclosure that still provides (...) (25 years ago, 15-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Using a 293B/293D combination
|
|
I read on this list over a year ago that you *can* piggyback the two different chips together and still get the spike protection from the L293D. It was explained that you don't need to piggyback two L293D chips, because one spike-protecting chip (...) (25 years ago, 15-Jan-00, to lugnet.robotics.handyboard)
|
| |
| | OxOc register
|
|
I had short circuit my TOC3 with a 5V source once. i changed the processor and the board worked. but i noticed that whenever i downloaded the pcode.s19 file, it wants to set the OxOD register instead of the OxOc. i downloaded config0c.s19 from the (...) (25 years ago, 15-Jan-00, to lugnet.robotics.handyboard)
|
