 | | Servomotor
|
|
i'm using digital pin 9 to generate the control signal for my TS-53 servo. however when i try to make it move, it only turns a little bit for the first command but just stops there, the motor continues vibrating though. the idea behind my code: set (...) (25 years ago, 4-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | pcbug11 EEPROM problem
|
|
Hi all, I hope you can help me with this: I am trying to get the talkeree installed on eeprom and when i use these commands ms $1035 0 eeprom $b600 $b7ff eeprom erase loads talkeree $b600 verf talkeree The verifying goes wrong. It bassically tells (...) (25 years ago, 4-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: please delete "Pretty Park.exe"
|
|
Hi - If you got it from a chineese named person it may not have been 'spam'. We got it at work and it wiped out one of our guy's computer completely. I got it from a somewhat familiar sounding name (chineese) but erased it last night because I knew (...) (25 years ago, 4-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Where is dl for unix?
|
|
(...) Another note regarding this: The dl that I'm using is an a.out version rather than an elf executable, and I quite often need to use it on a Red Hat 6.x version of Linux. Red Hat 6.0 and later doesn't have a.out support running automatically, (...) (25 years ago, 3-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: pcode for 20x4 LCD
|
|
(...) I think that i can help you. I do have the data sheets of the 'OPTREX DOT MATRIX LCD MODULE' It contains 47 pages,but i can filter the most interesting ones out for you,especially the ones on how to program the full 80 characters + the (...) (25 years ago, 3-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | pcode for 20x4 LCD
|
|
I picked up the 20x4 LCD at bgmicro, and it works fine. I have pcode for 20x2 successfully running, simply by re-compiling with the LCD_COLS set to 20. Does anyone have the mods required to support all 4 lines of the display? It looks to be beyond (...) (25 years ago, 3-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Where is dl for unix?
|
|
they're in the IC distribution tar file. see the link for Unix versions at (URL) fred. (...) (25 years ago, 3-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | decoupling capacitors
|
|
If i'm not going to use a separate power supply for the motors, it is advisable to use decoupling capacitors, right? what type of capacitors, what's its ratings (10uF or 1uF or?), and between which terminals should i connect it to? please reply (...) (25 years ago, 3-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Where is dl for unix?
|
|
Hi, I need to get the dl program to load the bootstrap code on my handyboard. I seem to remember that it used to live on the handyboard site with the contribution code, but I've pretty much had a look everywhere and could not find it. Anyone knows (...) (25 years ago, 3-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | please delete "Pretty Park.exe"
|
|
hi everyone, some bozo sent us spam with a virus on it. make sure to delete "Pretty Park.exe". i'm reporting the spam. it's a little confusing 'cause in the copy we received, it doesn't have handyboard@media as a destination anywhere. if spam (...) (25 years ago, 3-Dec-99, to lugnet.robotics.handyboard)
|
