 | | Motor Controller Question
|
|
From what I could figure out from the literature on the HB, the motor controller circuit is controlled by Port B on the 6811. With a little tinkerin last nite I was trying to set/reset some of the pins poking values into $1004 (Got this from "An (...) (25 years ago, 13-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Error at address 0x0000
|
|
Hi, That error message is actually to do with a fault in the Borland Delphi code for serial transfer, NOT a fault with the HandyBoard! (I use the same Delphi code in my HandyBoard terminal program as the program HBDL). It appears to manily occur on (...) (25 years ago, 13-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | RE: Stepper Motors
|
|
(URL) the interactive c page .-----Original Message----- .From: T.C. [mailto:dab8rs_85@yahoo.com] .Sent: Monday, October 11, 1999 3:49 PM .To: handyboard@media.mit.edu .Subject: Stepper Motors . . .Can anyone give me a sample program on how to (...) (25 years ago, 12-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | IR sensor for Program download to HandyBoard ??
|
|
Hi , I am new to Handyboard and have these IR questions. Can the IR sensor be used to download programs to the HandyBoard? my idea is to dynamically load programs to the handyboard using IR communication . or Can RF communication be used? Is is (...) (25 years ago, 12-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Error at address 0x0000
|
|
Hello, i have the same problem with the Error at address 0x0000. First i checked the hardware (Ram,Latch...) but i cant't find a bug. In the archive i found this message that descibe a softwarebug on faster machines. But i tested HBDL with a P133 (...) (25 years ago, 12-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Stepper Motors
|
|
Can anyone give me a sample program on how to control a stepper motor and were is a good place to but some that work good with the handy board. TIM ===== (25 years ago, 11-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard/ USB interface
|
|
i have tested several of these with Macintosh. I haven't tested any with PC, but i assume they should work. see (URL) for info on the Mac solutions. f. In your message you said: (...) d (...) (25 years ago, 11-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Handyboard/ USB interface
|
|
I have heard of USB to RS232 adapters- I was wondering if anyone has had any luck in using these devices to connect to the Handyboard? I recently purchased a new computer, but it only has 4 USB ports, and no RS232 ports!. (25 years ago, 11-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | RE: LM35 Again
|
|
Hi, Like an update to my prior email, I have tested the LM35 with an external power source, with the same bad result. Any help will be welcome. Thank You José Luis ----- Original Message ----- From: Jose Luis <hal9000@cvtci.com.ar> To: (...) (25 years ago, 11-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | someone looking for gearbox???
|
|
someone was asking about a gearbox for a project ` while surfing tonight I came across this I hope it is what you need <A HREF="(URL)Gearbox with motor</A> (URL) (25 years ago, 10-Oct-99, to lugnet.robotics.handyboard)
|
