 | | Re: ------( Terms of use for lugnet.com )------
|
|
Sorry about this mess below -- this only applies to people reading the HB list via the LUGNET server. The message below was auto-posted by the server when the new newsgroup (which is being gatewayed with the mailing list) was created. I forgot to (...) (25 years ago, 13-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: ------( Welcome to lugnet.robotics.handyboard )------
|
|
(This was a special message posted by the LUGNET server to the hb newsgroup, and subsequently echoed back out to the hb mailing list. The gateway preparations are about 98% complete. Still a few loose ends to nail down.) --Todd (...) (25 years ago, 13-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Four Wheel Base
|
|
Hi, Has someone tried a four wheel robot base using diferential traction?, I'm making this question because I'm not sure of the tree wheel configuration, in the last base that I made, the caster wheel has ever maked some bad influence in the robot (...) (25 years ago, 12-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Is there a device that...?
|
|
Peter, There are quite a few different products such as that. The two I use are: PicoScope & PicoLogger - (URL) - By TiePie Engineering (URL) Is there a device that connects to a computers COM or Parallel port that (...) Charles Hacker Lecturer in (...) (25 years ago, 12-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Debugging the memory circuit
|
|
We've assembled two handy boards up to the point where we are testing the downloader. In section 6.0.6 of the assembly guide, it says "If the download process appears to go correctly, but then the Handy Board does not boot with the Interactive C (...) (25 years ago, 12-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | ------( Terms of use for lugnet.com )------
|
|
TERMS OF USE FOR LUGNET.COM OVERVIEW AND DEFINITIONS lugnet.com ("LUGNET") is a privately owned Internet site designed and run primarily for the benefit of those who enjoy building with, discussing, collecting, buying & selling, trading, and (...) (25 years ago, 12-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | ------( Welcome to lugnet.robotics.handyboard )------
|
|
Welcome to lugnet.robotics.handyboard, a LUGNET discussion group. CHARTER/PURPOSE: lugnet.robotics.handyboard (group): Focused discussion group for the Handy Board device: distribution of information of any sort about obtaining, debugging, or using (...) (25 years ago, 12-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Is there a device that...?
|
|
You can try some IO cards. I don't know of any that connect to the ports but I know most can plug into ISA/PCI ports and have programmable I/O ports taht can be used by various differnt languages. I remeber somthing in the lines of "PC Systems (...) (25 years ago, 11-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Is there a device that...?
|
|
Is there a device that connects to a computers COM or Parallel port that can measure voltage, on different channels. All I need is a digital input like the HB. So if there is a signal it would report true and if there is no signal then it would (...) (25 years ago, 11-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: RF Module
|
|
Hi, Sorry I didn't get back to you yesterday. It sounds like you need to tune your radio modules. It could be your transmitter, receiver or both. If you don't have a function generator to create an input square wave for testing, you could try to get (...) (25 years ago, 10-Sep-99, to lugnet.robotics.handyboard)
|
