 | | 20 X 8 L.C.D driver?
|
|
I have seen questions on the list about using a 20 X 8 instead of a 16 X 4 lcd, I think that the person was told to look on the handy board site for a 20 X 8 driver. has anybody used a 20 X8 lcd and if so how did you do it and could you help me use (...) (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Serial Routines
|
|
Hi, I have the following questions: I want to transmit data by a radio comunication beetween HB and PC (only HB to PC right know) using the pa7 and a one-way wireless link from Conrad Electronics (german electronic reseller). Do i need the pa7_9600 (...) (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | RE: Sharp GP2D05?
|
|
I have used the Sharp GP2D05 with the Handy Board and found it to be extremely simple to use. It is easy to control in either IC or in assembly language and easy to adjust for range. There is a tiny potentiometer on the back of the unit that you (...) (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Java and 68hc11
|
|
Thanks, I downloaded all, and now i'm trying to make it run. Very, very interesting... ---...--- From: Pierre Deprost <Pierre.Deprost@Advalvas.be> To: Stefano Falconetti <falconetti@sigma.it> Subject: Re: Java and 68hc11 Date: 03 March 1999 22:20 (...) (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | RE: Sharp GP2D02 code available
|
|
Terry, Understand that the GP2D05 is a different device than the GP2D02. For the '05' you can set a analog threshold and the digital output read 1 or 0 depending whether the distance is according to this set threshold. The '02' device has a real (...) (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Are GP2D02 available in Australia
|
|
Hi all, Can anybody tell me from where I can get GP2D02 in Australia. Sincerely Javaid Iqbal (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Sharp GP2D02 code available
|
|
I just finished sending a question to the mail list but may have my problem fixed? Just from blind luck. I have digital out #7no the expansion board and digital in#15 on the main board and the first of the zeros on on the LCD changes to a one at (...) (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Sharp GP2D02 code available
|
|
Hi Barry, I have a GP2D05 from Acroname Inc., Have wired as per instructions black for gnd., green for Vin, Yellow for Vout, and red for Vcc.The pin outs are different than the GP2D02. Then installed the diode and connectors for the handyboard .as (...) (26 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | stepper motors
|
|
Hi : I am looking for a stepper motor that works at 7V. I was wondering if any of you have used stepper motors for the handyboard or the Rug Warrior. If so, what model did you use and what was your selection criterion for the motors. Thanks. (26 years ago, 7-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Where do I get Sharp GD sensors
|
|
I ordered mine from Acroname Inc. for $19.00. They also have sample code provided by Gary Livick. I haven't connected it to the handyboard as or this time but will be intersted to know how everyone else is doing it. Mine is a model GP2D02. Good Luck (...) (26 years ago, 6-Mar-99, to lugnet.robotics.handyboard)
|
