 | | Re: Visual Basic and parallel port
|
|
i know that this doesn't really have anything to do with the handyboard but has anyone tried to access the computer's parallel port with visual basic? =) chen (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: electronics question please help
|
|
Bob - - Here is a link to the 74HCT04 data sheet: (URL) that this helps. - - - Nick - - - Bob Kelly wrote: <snip> (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | electronics question please help
|
|
Hello all, I hope there is a simple answer for this... I have attempted to build the circuit that will allow IR object detection using the Sharp IR detector module and a pair of "high output" infrared LEDs. The circuit I built was the one from (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Book Review ???
|
|
Does anyone have any comments about "The Personal Robot Navigator". It is sold by (URL) about $50. I have read (and continue to read) "Mobile Robots: Inspiration to Implementation" and think it is a *must read*. TIA - - - Nick - - - (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: IR question
|
|
(...) I just looked over the code again, and you're right, I see no reason why it shouldn't work. I guess the comment is just left over from a previous version where it did make a difference. This is not something I can test though, so I'll have to (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | HB to create video displays?
|
|
I am thinking of putting a wireless board-level color or B&W camera on my Mobot and I have a question for all the techies. Is it possible to use one of the different outputs on the HB to interface with the camera to put diagrams on the live picture? (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Need Handy Board memory debugging software
|
|
Gentlemen: I'm having a bit of trouble with my handy board's display. The board itself works, and I've swapped out old display for a new one. I suspect the memory or transparent octal addressing latch to be at fault. I understand you've memory (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Shaft encoder sensors...
|
|
Zagros Robotics sells them for $7.00 ea US (URL) Message----- From: John Vaughn <vaughn@HWS.EDU> To: Kat <khorvath@up.edu> Cc: handyboard@media.mit.edu <handyboard@media.mit.edu> Date: Monday, February 22, 1999 10:23 AM Subject: Re: Shaft encoder (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | RE: IR question
|
|
I found that article listed at: (URL) It was in the January 1999 issue, titled: "Multiprocessor Communications Part 1: Methods for Communicating " Maybe it wasn't 68HC11 specific after all. Gerald (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | RE: IR question
|
|
James, I'm not sure if this is the correct answer since I am new to the Handyboard, but I think it is: If you do not disable the IR Input Interrupt, your transmission could be 'interrupted' by the receiving information and this may mess up your (...) (26 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
|
