 | | Expansion Board Files
|
|
I have not got my expansion board files to load! what am I not doing correctly? Help !! I have deleted all my ic files, reloaded 3.2 from Newton Labs in c\ic. In ic I have : expansion-libs libs ic.help ic.ini ic.win.exe install.log I can load ic but (...) (26 years ago, 25-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Serial LCD on PA4?
|
|
I am trying to send serial data to a 2-Line LCD which is connected to Scott Edwards' 9600baud backpack. I have PA4 available. I came across Fred Martin's 'Pa7_9600' serial files which included Pa7_9600.asm and Pa7_9600.icb and am wondering if they (...) (26 years ago, 25-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Analog Ports
|
|
yes, it's the 47K pullup that's causing the IR's to not work. slice through the trace connecting the 47K to the sensor input pin on the underside of the printed circuit board. fred In your message you said: (...) (26 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Interactive C-OS8 Downloading Problems
|
|
cappy, did you use my new "6811 Downloader MCL" version? this has been tested on a variety of Macs running system 8.5 and 8.1. please download it from (URL) me know if this works to download from your 6500. have you ever used the serial port on this (...) (26 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Analog Ports
|
|
I have the MTJPRO11 board by Mekatronix as well as the MIT HandyBoard both use the 68HC11A1FN mcu. I am using hacked Sharp GP1U58 'tin can' detectors so that they output analog voltage from 1.5 to 2.5 ( effective proximity range is approximately 4" (...) (26 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Interactive C-OS8 Downloading Problems
|
|
I have nearly teared my hair out trying to get my HB to to DL on a my OS8 6500 Mac. I though there might be someting wrong with the HB and replaced 5 chips. Today I took my HB over to a friends house who has a Performa 475 and hand had no problems. (...) (26 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Wirz LMD18200
|
|
I'm not familiar with the Wirz board, however the board I built used the regular "motor output" of the handyboard with no modification required. The trick was to use an opto-isolator to "recover" the forward and backward logic states. That was done (...) (26 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: batteries port
|
|
(...) That sounds like too much voltage for the HB. I think I remember reading that the HB runs on up to 12 V max. Check the Handy Board Technical Reference. There are much better ways to run motors that require higher voltages. Try using a separate (...) (26 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Stack Overflow
|
|
(...) If your code looks something like this... if (i == 1) do001(); else if (i == 2) do002(); else if (i == 3) do003(); else . . . if (i == 100) do100(); ...then try changing it to this: /* Not really a loop, just so we can break */ for (;;) { if (...) (26 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Wirz LMD18200
|
|
I just checked it. It is www.wirz.com Happy shoping Pherd (26 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
|
