 | | Photocells?
|
|
I am seeking help in locating suppliers of quality photocells or light sensing equipment suitable for use in a handyboard environment. Thanks! (26 years ago, 29-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | http://tcw2.ppsw.rug.nl/hb/hbassem/index.html/join mailing list
|
|
I wish to join the handy board mailing list. (26 years ago, 29-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | DC Motor Manufacturers
|
|
Hello everyone, Has anyone found a good source for DC motors? I am looking for small motors to use as direct drive movement of a small 1.5 LB robot. Any help is greatly appreciated! Bill Denzel Senior Mechatronics Student California Polytechnic (...) (26 years ago, 27-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Downloading problems
|
|
I haad similar problems and then I realized that I did not need to download pcode or anything special. I just ran IC and it connected -- all the ports are working fine... Scott Sherman (...) (26 years ago, 27-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Downloading problems
|
|
(...) please download the latest 6811 Downloader for Macintosh, just posted last week on the HB web site. Fixes compatibility probs. (...) th the (...) OK, yes, you've already downloaed. (...) plus (...) please download these files from the HB web (...) (26 years ago, 27-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Downloading problems
|
|
Fred This is a followup to your answer regarding downloading problems 1. The 6811 Downloader does not seem to work with HB. I get mesaages varying from recieved 0, wanted 255-or serial port not responding. I am DL from a MAC PPC 6500 OS 8. 2. This (...) (26 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | RE: servo motor
|
|
Since the System 3000 servos appear to be made by Futaba, and they specify a standard Futaba "J" connector, my guess is that they would plug right in. Futaba practice is as you state: red=5V, black=common, white=signal. Brett Anthony -----Original (...) (26 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: CHARGER BOARD PROBLEM(URGENT)
|
|
phillip, please go through the sequence of tests in the assembly directions (as if you were building the serial/charger board from scratch), and indicate the point at which you first detect a problem. (URL) your message you said: (...) (26 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Downloading problems
|
|
Use 6811 Downloader to download pcode_hb.s19. Power cycle, and the Handy Board should beep and display a version message on its LCD screen. Then, run IC modem or IC printer depending on which port you are using. It should be configured to boot with (...) (26 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Downloading problems
|
|
I assembled the HB board some 2.5 years ago. At that time it seemed to work very well. The hook is that I'm quite strong on the Hardware side and rather anemic with regard to software. In the earlier time I would download it from a Mac 11si-no (...) (26 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
|
