 | | RE: Question for Fred
|
|
That's a funny question. I just finished a class on this exact topic. The basic determining factors when deciding whether to use a stepper motor or a DC brush/less servo motor is speed and open/closed loop control. Stepper motors are limited to (...) (26 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Do It Yourself RF module????
|
|
Hi, Now that the topic of RF commucation seems to arise again, I have a question too. After looking at the RF modules of radiometrix and linx I concluded that: 1. They are too expensive 2. They are probably not available here in the netherlands (...) (26 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | RE: Help with overcharged batteries
|
|
<<Last night we discovered that we had left our Handyboard on ZAP when we thought <<we had left it to trickle. It was left at this condition for about 6 hours. You probably should remove the battery pack, put it in a baggie, and take it to Radio (...) (26 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | RE: Serial interface/ RF data link
|
|
<<snip>> Unfortunately, I have not had any luck. This brings me back to the first point- is it possible to use the serial interface board by just providing the tx and rx lines? <<snip>> In short, no. The serial interface board takes power from the (...) (26 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | persistent var's in IC
|
|
Has anyone had problames with the Handyboard, IC 3.2 and 'persistent' variables? the following declaration works fine : persistent float i; but using an array: persistent float battery_voltage[ 320 ]; always causes an error while downloading : IC> (...) (26 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Serial interface/ RF data link
|
|
To properly comunicate with any PC you need to convert your TTL TX and TTL RX signals coming from the Handy Board to RS232 voltage levels. The charging board contains this interface IC called the "MAX232" The power wire is required unless you are (...) (26 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Help with overcharged batteries
|
|
Last night we discovered that we had left our Handyboard on ZAP when we thought we had left it to trickle. It was left at this condition for about 6 hours. This morning the motors are running very sluggish. Are our Handyboard or its batteries (...) (26 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Serial Interface/ RF data link
|
|
Sorry, the kit is from LINX Technologies (not LYNX) <A HREF="(URL)Linx Technologies -- Products</A> (URL) (26 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Serial interface/ RF data link
|
|
Let's say I want to use a serial interface board without the "charger", as the one provided with the Handyboard kit. The Tx and Rx lines are obviously required, but what about the ground and power lines?... Speaking of "easy to interface" data link (...) (26 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | RE: expand memory HB
|
|
I'm running IC 3.2 and am curious why this fails : #define HOURS 10.0 /* hours of logging */ #define INTERVAL 5.0 /* minutes between samples */ #define SAMPLES ( (60/INTERVAL)*HOURS + 1 ) float battery_voltage[ SAMPLES ]; the message on download is (...) (26 years ago, 8-Dec-98, to lugnet.robotics.handyboard)
|
