 | | sonar
|
|
what program to control about 2sonar.jpg? how i adjust program (sonar.c) for 2 sonar in picture 2sonar.c? (28 years ago, 2-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Hacking Servos
|
|
Thank you all very much for your help :) Best, Andre. (...) ===...=== Andre Philippi - Applications Developer | Phone: 626-296-5016 philippi@corp.earthlink.net | Fax: 626-296-5113 Earthlink Network, Inc. | 3100 New York Drive (URL) | Pasadena, CA (...) (28 years ago, 1-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | RE: Hacking Servos
|
|
Yeah, I remember seeing that one; I may actaully have the info at home... Anyway, an R/C servo has a hard stop to limit travel because the electronics use a simple potentiometer on the output shaft for position feedback. These pots typically have (...) (28 years ago, 1-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Hacking Servos
|
|
(...) I put together a page with detailed instructions that has been used by a number of high school students without any problems. The robot is based on a Basic Stamp but the servo modifications are easy and work with any controller. (URL) (28 years ago, 1-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Hacking Servos
|
|
Howdy Folks :) I remember reading a web doc a while ago on how to convert servos so their shafts can rotate more than 180 degrees... It was a nice doc, with pics, schematics, and everthing... but I lost the URL... :( Does any one know what doc am I (...) (28 years ago, 1-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: HandyBoard and iMac?
|
|
It doesn't bother me that much: I haven't used a floppy in two or three years. I have ISDN at home: it's way faster than a floppy ;^). -- Eric (...) (28 years ago, 1-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | 2sonar
|
|
i use circuit on 2sonar.jpg . if i use sonar.c program, how i adjust this program for 2 sonar trasducers. ?(a picture on 2sonar.jpg) i want to 1 sonar working single , don't together.or to alternate. Sonar number 1(#1)is working until check (...) (28 years ago, 1-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | 2sonar
|
|
i use circuit on 2sonar.jpg . if i use sonar.c program, how i adjust this program for 2 sonar trasducers. ?(a picture on 2sonar.jpg) i want to 1 sonar working single , don't together.or to alternate. Sonar number 1(#1)is working until check (...) (28 years ago, 1-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | 2sonar
|
|
i use circuit on 2sonar.jpg . if i use sonar.c program, how i adjust this program for 2 sonar trasducers. ?(a picture on 2sonar.jpg) i want to 1 sonar working single , don't together.or to alternate. Sonar number 1(#1)is working until check (...) (28 years ago, 1-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: HandyBoard and iMac?
|
|
hi eric, i haven't tried any of these products, but they *should* work. the mac hb software uses low level driver calls, so if that stuff is patched and translated to usb, it would work. but if i were you i'd get one and try it on an existing (...) (28 years ago, 1-Dec-98, to lugnet.robotics.handyboard)
|
