 | | Re: Expansion interface status
|
|
(...) Build a 68360 in the expander board, that'll get ethernet, and multiple SCI ports. All the IO anyone should ever need. :-). (28 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
| | RE: Expansion interface status
|
|
While I welcome the small kits, they introduce interface issues for beginners, especially if there are multiple kits attached simultaneously - seems like this is a problem the expansion board should be solving rather than causing. The value I am (...) (28 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
| | FW: 6 servos
|
|
RS232 is +12 and -12, but most serial ports can work correctly even if the signal is 3 to 5v. I regularly use 3 to 5v level serial signals. If you need to convert low voltage serial to RS232 specs, you can use a chip like Maxim's 232 - see (...) (28 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
| | Re: 6 servos
|
|
(...) There are two types of serial voltages: TTL level and RS-232 level. The HB's serial interface board converts from TTL to RS-232 for communicating with the host computer. The Scott Edwards board accepts TTL levels, so an HB pin can drive it (...) (28 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
| | Re: 6 servos
|
|
(...) Are the digital outputs at 5v high? I think you mentioned on the HB homepage about the serial interface converting RS232 levels at +12 and -12v to TTL levels (5v). I'm not that familiar with the nitty gritty of RS232 so this kinda puzzles me. (...) (28 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Expansion interface status
|
|
(...) Yes. The current status is "on hold" while I rethink the feature set. I'm considering doing something more like Scott Edward's little servo board for HB expansion: that is, a collection of small, physically detached boards. For servo's, I (...) (28 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
| | Expansion interface status
|
|
Does anyone know the current status of the expansion interface? My poor handy is at capacity for some i/o functions ;-( (28 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
| | FW: 6 servos
|
|
This would be a very powerful enhancement to the handy-board. It would obviously allow easy communication between the HC11 and PIC boards. Since my application will use 2+ PICs in addition to the Handyboard, it would allow easy networking of all 3 (...) (28 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
| | Re: 6 servos
|
|
This multiple servos thing is reaching FAQ status, and here is how I plan to deal with it. Scott Edwards Electronics sells a cheap ($30 kit, $45 assembled) servo board that drives 8 servos. You can gang them to get 32 servos or even more. The boards (...) (28 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
| | 6 servos
|
|
Hi all, I want to build a six legged walking robot using the handyboard. I want to use 6 servo motors for that. I heard that the handyboard can only control 2 servos, but that there is a servo controller board which can control up to 32 servos, (...) (28 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
