 | | RE: HandyBoard LCD Module
|
|
I am aiming on using the 16x2 LCD from Maplins (part number DK63T, 8.89 pounds + vat, model number LM016L). I don't know of hand if the pin layout is the same as the LM052L listed in the parts list but as I am going to be using a connecting lead (...) (26 years ago, 16-Oct-98, to lugnet.robotics.handyboard)
|
| |
| | Douglas HB Boards Predrilled?
|
|
This is a simple enough question -- are the blank handy boards from Douglas Electronics pre-drilled? Thank you. john calhoun- (26 years ago, 15-Oct-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Douglas HB Boards Predrilled?
|
|
Yes ... mine arrived today and they are of good, finished quality... Owen (...) (26 years ago, 15-Oct-98, to lugnet.robotics.handyboard)
|
| |
| | Vector 2X
|
|
After reading the Vector 2X Manual a couple of times, it seems that the SDI pin (Serial Data In) has no function. It is even stated in the manual that this pin is never connected. If this is the case, couldn't we use the MISO pin from the HandyBoard (...) (26 years ago, 15-Oct-98, to lugnet.robotics.handyboard)
|
| |
| | Re: HandyBoard LCD Module
|
|
Hi, any LCD Display 2*16 with a Hitachi HD44780 Controller will do. There are several retailers. But I do not know about the UK. Batron, Rohm (the HB original) are just two producers of LCD Displays. (...) (26 years ago, 15-Oct-98, to lugnet.robotics.handyboard)
|
| |
| | Re: HandyBoard LCD Module
|
|
Try Farnell order code 325-351. It's more expensive than it has to be, though. (...) (26 years ago, 15-Oct-98, to lugnet.robotics.handyboard)
|
| |
| | HB is just fine the way it is. [was: RE: The HandyBoard Mailing Lst]
|
|
(...) Erm... not quite. I much prefer an email based distribution. I don't access the net interactively that often. I just queue up my mail, and my computer autonomously purges each evening while I sleep. If the handyboard list were a newsfeed, I (...) (26 years ago, 14-Oct-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Wireless Link to HB
|
|
Dave, See (URL) for complete scematics to connect a BBiM 418 F FM transmitter/receiver to your HB! (thanks to Jan Sipke van der Veen for these scematics) Jeroen van der Vegt. Jeroen van der Vegt, A.J.vanderVegt@ITS.TUDelft.nl (26 years ago, 14-Oct-98, to lugnet.robotics.handyboard)
|
| |
| | Some Questions
|
|
Hello, I have several HandyBoard questions: 1) How can I determine ( or does any body know ) the baud rate at which the PC communicates with the Handyboard? 2) When IC attempts to Synchronize with the Board, what is going on "Behind the scenes"? 3) (...) (26 years ago, 14-Oct-98, to lugnet.robotics.handyboard)
|
| |
| | Re: cannot communicate
|
|
Hi All, Thanks a lot for the help. I just dont know what we would do without this mail list!! All you need is a little direction when things are going wrong. I had switched cables from my 6.270 board. THANKS A MILLION GUYS. Choo, The v2x compass is (...) (26 years ago, 14-Oct-98, to lugnet.robotics.handyboard)
|
