 | | HB and the Bloomington HS Solar Bike Team
|
|
Hello All, I posted a little note a while back about our use of the HB on the two bikes that our local high school is using in solar bike races in Topeka and Akita, Japan. Well the races are over and I thought that some of you may be interested in (...) (26 years ago, 31-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Need PWM generator chip
|
|
(...) look for the LM629 on the national semiconductors (URL) offer free samples. However, the one i'm talking about is surface mount. .---...--- . . . | Remi Desrosiers | "My Youth in Arcadia" ICQ# 7228856 | harlock@videotron.ca . (...) (26 years ago, 31-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | beginner
|
|
Hi every body... I need help guys! So far in my life I haven't done any thing like this, but I like to learn. Is there an idiot's guide for a beginner to start programming a handy board? Can some body tell me where to buy a handy board and which (...) (26 years ago, 30-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Need PWM generator chip
|
|
I'm looking for a chip that will generate PWM waveforms. I know they exist, but I don't have information at my fingertips. Thanks for any tips! --greg ***...*** * Greg Starr, Professor * * Department of Mechanical Engineering ph (505) 277-6298 * * (...) (26 years ago, 30-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | IC floating point bug
|
|
Has any new information on the IC floating point bug come up? I have been coding neural networks into my robot and was having problems. A simple 'test' network of simple values ran fine, but when I manually entered a real evolved network with many (...) (26 years ago, 29-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: recherche de logiciel C Interactif comme prisenti dans le livre
|
|
please see (URL) your message you said: (...) (26 years ago, 29-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | recherche de logiciel C Interactif comme prisenti dans le livre
|
|
N'ayant pas accés à un micro équipé d'un lecteur de disquette et ne connaissant rien du protocole FTP, je souhaiterais obtenir de votre part la version Gratuite du C Interactif Mes coordonnées : Claise Jerome 23 avenue marcel pagnol 60870 villers st (...) (26 years ago, 29-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: 68hc11F1
|
|
Hello mike, (...) I also wanted a small board with MCU, memory, serial and a bus to the outside world. This way i made a general io board and could connect anything to it. (...) You can buy the hc11F1 in 4 speeds, with a freq up to 16 Mhz, setting (...) (26 years ago, 29-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: What types of IBMs does IC Run on?
|
|
i'm pretty sure the DOS version of IC runs on 286's -- it may even run on 8086's that have the 8087 math co-processor. fred In your message you said: (...) (26 years ago, 29-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Digital In and Analog Out Header
|
|
It should read: ooo...ooo Signal ---...--- ___...___ 47K RESISTOR NETWORK ___...___ ooo...ooo +5V ---...--- ___...___ ooo...ooo Ground ---...--- Regards, Patrick --00---...--- Low cost MIT Handyboard supplie (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: AC adaptor
|
|
Hi All, That color code on inductor should read: BROWN(1), BLACK(0), GOLD, SILVER which is (1x10^0)uF => 1uF. Sorry for the confusing and we will mark that in the future. Thanks. Patrick --00---...--- Low cost MIT Handyboard supplier and Official (...) (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: What types of IBMs does IC Run on?
|
|
I would guess this means that IC needs a math co-processor, in other words, a 486 DX or higher. -- Justin Kao <jkao@bigfoot.com> <jkao@flash.net> <ICQ 5903051> (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | interfacing V2X compass
|
|
HB Folks, I'm currently using the HB to interface to a Vector 2X compass. I'm using the compass in RAW slave mode, so it's different than the hardware interface that's documented on the HB web site. But I did notice that the documented interface (...) (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | polaroid ultrasonic detector
|
|
I'm trying to make the polaroid ultrasonic motion detector compatible with the crickets. Does anyone know where I can find a data sheet for these detectors? I unfortunately broke the last one I was using. I think I must have exceeded either the (...) (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: IC Floating Point Bug
|
|
(...) If you notice, the constant is PI/2. If you add more significant digits you can even get "a/b" to become 0.5, that is twice the correct answer rather than half of it!!! The reason the bug concerns me so much is that since "a" and "b" print out (...) (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: AC adaptor
|
|
Please see the FAQ for the answer to the adapter question: (URL) the L1, that substitution may or may not work. try it; if your motors don't work right, it could be that. Fred In your message you said: (...) (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | What types of IBMs does IC Run on?
|
|
Greetings, I have recently gotten the free version of IC working. It was a battle and it seems that the type of host processor makes a difference. Running IC on an old IBM XT (8088) CPU produces the following error whenever a routine using floating (...) (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: IC Floating Point Bug
|
|
(...) <snip> I get the same results with version 3.2. Curiously, if I remove the last digit in the a = 1.570796 statement (or replace it with a zero), then I get the correct answer. I guess it has something to do with specifying too many significant (...) (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | AC adaptor
|
|
I figured out all of my problems were caused by using an ac-dc adaptor with the wrong voltage. What is the correct output voltage for the adaptor that should be used with the handyboard? Also, I cannot find L1, the iron core inductor. I ordered my (...) (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Update
|
|
Sorry, not the handyboard but the expansion board Bill James | work: 972.480.2306 Product Test Specialist | Pager: 972.598.6201 w-james2@ti.com Precision Analog & Interface Department Polymath in Training | Have Spacesuit will Travel (26 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
|
