 | | ASM 96
|
|
Hi, sorry to drift from the point of this mailing list but I have a question for all the 80C196 users out there. Does anyone have ASM 96? I have been searching for it for weeks now, without any luck. The only thing I can find about it is updates to (...) (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: assembler
|
|
Hi all, Would be great if messages were sent in plain ASCII... Andre Ramos (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: assembler
|
|
Hi Richard, Sorry for my bad english (normaly i speek german). The 68hc11 has differnt kinds of addressing-modes. 1) LDAA #65 : immediate adress, The value is stored in accumulator 2) LDAA result : direct Adress The value from adress RESULT is (...) (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | assembler
|
|
Hello, can anyone tel me the function of the # in the AS11 assembler, i'm new at assembler programming and get sometimes confused about the usage of the # # means a number, but what's the difference between: ldaa #$1000 and ldaa $1000 Thanks, (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | External ram
|
|
Hello all, I have an 68hc11F1 and 32 K of external ram and 32k of flsah. I have the 16 mhz version of the hc11. While having problems to program the flash suggestions from the list where that i probably had a timing problem. So i reduced the (...) (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Sorry: Re: Inclinometer for Handyboard
|
|
I humbly apologize for the time and bandwidth I forced on everyone with my intended-to-be-small...-and-dirty sketch on the inclinometer. I honestly did not realize the size of the file when I sent it or I'd have found a much better way of doing so. (...) (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: check_sensors.c
|
|
Hi Joe&David,All, Let me explain what I would like my handyboard to do. Guide a lawnmower by detecting the border of cut and uncut grass. Monitor a row of 16 +or- ir emitter/detector pairs placed about every two inches to report to the motor control (...) (26 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | IR, bitmapping
|
|
I was just wondering if you could get the handyboard to transmit other than just in 125 hz or 100hz. Also...has anyone done anything like making a robot follow another using the ir transmit? Has anyone had any success using shaft encoders to make (...) (26 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Inclinometer for Handyboard
|
|
greetings everyone, this is a reminder to please NOT send 1MB attachments to the list! In the guidelines I sent you when you were subscribed to the list, I stated a limit of 50 KB (that's kilobytes) for any message. Please remember that your message (...) (26 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: ic help
|
|
Hi LLya, Actually, descriptions of these functions are described in HB manual, at least mine has. peek() returns integer value for the given location passed in as the parameter. For example: value = peek( 0x200); The peek returns the int. value (...) (26 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
|
