 | | MODB - How Is Expanded Mode Entered
|
|
If MODB pin is always grounded, how does the MCU get into expanded mode to access the 32K SRAM? The data sheet shows MODB HIGH to enter expanded mode. It show MODB LOW to enter single chip mode. What am I missing? -- ---...--- ipscone@halcyon.com (...) (26 years ago, 2-May-98, to lugnet.robotics.handyboard)
|
| |
| | Connections
|
|
Please forgive this probably silly question; as a software person I only dabble in hardware as a hobby: I want to make my own little expansion board and it requires signals from the expansion connectors of the HandyBoard. In particular I want to run (...) (26 years ago, 2-May-98, to lugnet.robotics.handyboard)
|
| |
| | 6.270 board
|
|
What is 6.270? Where did this number come from? ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the Advancement of Science and Art (...) (26 years ago, 2-May-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Testing with PCBUG11 - Getting Close
|
|
My problem turned out to be with Win 95. If I boot to DOS the PCBUG11 program works fine. It fails to work when working from a DOS window. I can now communicate with the MCU so my RS232 must be fine. When working from the command line in PCBUG, I (...) (26 years ago, 2-May-98, to lugnet.robotics.handyboard)
|
| |
| | Testing with PCBUG11
|
|
I have assembled the HandyBoard up to the point of adding the SRAM. I am still waiting for my SRAM to arrive. But, I want to check out as much as possible. Every step checked out fine to this point. I have two options at this point. I have an 6264 (...) (26 years ago, 2-May-98, to lugnet.robotics.handyboard)
|
| |
| | controlling a DC motor
|
|
Hello, i am currently trying to control a DC motor's motion (direction, speed, etc). Besides using a motor driver chip such as L293D, what else can i do to control the motor's motion?? Say, is there a method which can control the motor by totally (...) (26 years ago, 2-May-98, to lugnet.robotics.handyboard)
|
| |
| | DS1233 Monitor Chip
|
|
I cannot locate a DS1233 chip. I have tired DigiKey, Jameco, Mouser, Active. What is a good source for this part? I have an MC34064. Looks similiar except that it has no 350mSec delay and a different pinout. Has anyone tried this chip without any (...) (26 years ago, 2-May-98, to lugnet.robotics.handyboard)
|
| |
| | Schematic & PCB freeware
|
|
Ivex has a very good schematic and PCB layout demo at www.ivex.com ,the only difference between the demo an the full version is the demo is limited to 100 pads. (26 years ago, 2-May-98, to lugnet.robotics.handyboard)
|
| |
| | Max232CPE Substitutions
|
|
I used a Max202 in place of the Max232. I installed it with the 10uF caps. Since the 202 can be used with .1 and I already installed the 10uF ones. I decided to switch it for a 232. The 202 checked out (V wise) like the installation instructruction (...) (26 years ago, 1-May-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Schematic drawing - freeware ???
|
|
Try to look up MicroSim ...or something like that name. It has a crippled evaluation package that may suit your needs. I think the company is the developer of psplice. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics (...) (26 years ago, 1-May-98, to lugnet.robotics.handyboard)
|
