 | | Re: Help!!!! Handy Board Problem
|
|
I am going to guess this is a software problem on the PC side. If you can boot your computer in DOS mode, try running IC then. Or find an older box :-(. Freeware DOS IC is known to have serial line comms bugs with some fast machines. NT can't be (...) (27 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Size Conversions
|
|
I apologize in advance as this question is completely of the list topics but I hope that somebody will have the answer. I am currently building a six legged walker using the Handyboard as the main CPU and using a modified Miniboard using the Servo16 (...) (27 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Microphone on a Handyboard
|
|
If you need more than a +200 gain, try an LM358 in single supply mode and use +5v. These are fantastic op-amps and widely available (Digikey). jm (...) (27 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: digital ins
|
|
If you want to exaggerate the response, perhaps a LM339 +5v single supply comparator will do. Set up your circuit to go high(+5v) above your 2-3v range of operation. This solves all your input problems. Loads of manufactures make this thing. Data (...) (27 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Microphone on a Handyboard
|
|
(...) Assuming you've hooked the LM386's ground to ground and the + voltage to 5v, you should be set hooking the output of the LM386 to the analog input. Do not insert a capacitor in series, as might be shown for hooking up the LM386 to a speaker. (...) (27 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | microphone as a sound sensor?
|
|
Hi all, has anyone interfaced a microphone to an analog input of the HB? I've amplified the signal with an op-amp (LM386) but can't figure how to integrate the (AC) signal into a usable voltage range for the HB. I don't think that just rectifying (...) (27 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Manipulate the LCD in assembler
|
|
I have write a code for manipulate the LCD in the handy board. Because i can't use a battery backed RAM, i need to write in assembler. Well , i'm really read all the FAQ for LCD and for Handy board (including the apendix B for the 6270) .I'm using (...) (27 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Help!!!! Handy Board Problem
|
|
Hi! I'm currently assembling the handy board, and i got to the stage where i have the bare minimum to run IC. The problem starts when I try to send commands from IC (ver 2.851) to the handy board (running v 2.81). About 85% of the time i get the (...) (27 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | 68HC11's inputs
|
|
John, Thanks for the excerpt. Ouch. On first read, it looked like the 6811's input pin was beefier than I had originally thought. On my second reading, I realized that my hack probably is in fact outside the specs for the chip, so if you're trying (...) (27 years ago, 27-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: digital ins
|
|
(...) From the pink book (rev 3): pp. 2-24,25 "2.4.3 Internal Circuitry - Digital Input-Only Pin ...When the pin current is increased to very high levels (typically more than 100mA, specified limit is 25mA), physical damage can result. [...] As (...) (27 years ago, 26-Aug-97, to lugnet.robotics.handyboard)
|
