 | | Re: LM34 temp sensor to handy board?
|
|
Jeff, I used a couple of the 10mV/deg Kelvin ones, with nothing more than the current load resistor, ie no amplification at all. For example, freezing point = zero celcius = 273 Kelvin = 2.73 volts. With the 6811 resolution of about 20 mV (5v / (...) (27 years ago, 22-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | headers
|
|
This may sound like a dumb question, but I don't know where to get headers. Digi Key has some but 4 different kinds. The parts list says nothing except 14 pin female header. Nothing else. Where did you get your headers and what are the part numbers? (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo control using Miniboard slaved
|
|
Chuck: I agree with you; what I've done with the MiniSSC is to break the path into a set of linear segments with via points in joint space. The lynxmotion arm ends up needing a lot of points (therefore moving pretty slowly) to avoid jerkiness, but (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: LCD display
|
|
(27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: LCD display
|
|
Hi. Give me the location and phone number to this place that you can order them and I will consider ordering several and selling them off individually. Scott sherman@plains.nodak.edu CSG ITS NDSU (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | LCD display
|
|
Hi there, I'm in the midst of ordering all of the parts necessary to assemble the Handy Board. However, I'm having trouble finding two parts. They are the following: Description Catalog No. Manufacturer ---...--- ---...--- ---...--- Infrared (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: FW: Serial Communications.
|
|
Hi Fred: The Mini SSC does have a TTL-mode, but it needs inverted data i/o mode. Rather than figuring out how to do that in s/w I just used the MAX232 because it was easy and it made debugging easy into a dumb terminal program on my PC. I've had (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo control using Miniboard slaved to Handyboard.
|
|
Using the Miniboard as a servo slave is a good idea, perhaps even easier is to use a BOTBoard since the BOTBoard doesn't have any motor drivers hooked up to it (no PCB modification required.) Using the MiniSSC is "ok" but for controlling multiple, (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: FW: Serial Communications.
|
|
Mike -- Doesn't the Mini SSC have a TTL-levels mode, making the MAX232 unnecessary? Please send your serial output code, though. that would be good to distribute. -Fred In your message you said: (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | FW: Serial Communications.
|
|
Hi John: I've used the HB to send serial command strings to a Mini SSC (for the Lynxmotion arm). I built a tiny daughterboard with a MAX232 that plugged into J6 on the board for power. Software handshaking is minimal and the MiniSSC works fine. If I (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
