 | | Re: IR Collision avoidance
|
|
(...) I have a few questions for you. How did you combine the 38khz and 500hz signal. In a design that I am working on now I have two signals similar to yours and an enable signal running into a three input AND gate. I haven't built it yet but it (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | motors
|
|
Hi, Yes, that schematic posted by Prabal was exactly what I meant. I sent you the bmp anyway, Adam. David (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: motor voltages
|
|
Adam, I think David meant something like this: |---|<|---|<|---|<|---| M+ ----x x----(motor)---- |---|>|---|>|---|>|---| | | M- ---...--- That way you have a voltage drop AND conduction in both directions. - Prabal (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | where to get a board.
|
|
hello. i'm new to this mailing list, and would like to purchase a handy board. i'm curious if there i a place where i could perhaps find a used one (in working order), or who the best (read: cheapest) distributor is. thanks for info you can provide. (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Servos and Handyboard.
|
|
you can't power 2 servos from the hb's own +5v supply. get a separate 5v supply (linear regulated, *noT* a switching supply, OR batteries) and run your servo power from that. connect this external supply ground to the HB motor ground (on J13). -Fred (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: motor voltages
|
|
David, I would be interested in seeing a schematic on the wiring of the diode array. I am not sure of how it goes - exactly. I'm not located near a dedicated fax. I was wondering if it might not be too much trouble to sketch the schemtic on some (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Servos and Handyboard.
|
|
Hi Everyone. I'm doing a project on controlling servos using the handy board (actually, I'm building a camera rig with servo controls and interfacing this tho the www) My problem is this: when i try to control both servos at the same time, using the (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | as11 assembler
|
|
Hi, This may be a dumb question, but I hope someone will oblige me anyway. I was checking out the handyboard website, and I wasn't able to find a PC version of the as11 assembler. Does anyone know where I can get a copy? Thanks, Maria ---...--- (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: D0 - D7
|
|
Mar, This is what I've learned about the handyboard so far, and hopefully it will give you a little insight into what's going on with D0-D7 (the external bus). Because of the way the handyboard is configured, it's operating in special test mode. In (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: More Motor Speeds
|
|
go to the software resources page, and then follow the link named "Interactive C for the Handy Board source code and information". -Fred -- This message was composed using Articulate Systems' PowerSecretary, a Macintosh-based speech-to-text (...) (28 years ago, 2-Mar-97, to lugnet.robotics.handyboard)
|
