To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 781 (+10)
  RE: Best Lego Kit with Micro-motors
 
Found them from (URL) 1.800.835.0686 Fax: 1.316.231.3406 E-mail: pitsco@pitsco.com (URL) Message----- From: lugnet.robotics@lugnet.com [mailto:lugnet.robot...ugnet.com] Sent: Friday, November 20, 1998 10:02 PM To: lego-robotics@crynwr.com Subject: (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  RE: Surveillance Robot
 
(...) Rumor has it the Mars exploration set will have a camera, but there's no confirmation as yet. Daniel "Dan'l" Miller Senior, School of Aeronautics and danielmi@expert.cc.purdue.edu Astronautics, Purdue, Indiana danielmi@cartoon.ecn.purdue.edu (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  RE: Worm Drive Question
 
If you do not want to be limited to four floors you could have one long rod with "bumps" at every floor. With something sticking out of the elevator car, you know you have reached a floor everytime the rod is lifted from the ground. If you want to (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Re: legOS
 
Guys, Everyone seems to be missing one point: The RCX does have ROM code (this is what loads the firmware the first time, right?). If you were to "jam up" the firmware, you could just simply remove the batteries, let the firmware (which must be in (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  RE: Worm Drive Question
 
This is exactly what he was proposing without the bottom floor sensor, his problem however was how to tell the elevator where to go, with only two sensor slot left he can only input a 2bit number ie from 0 to 3 hence four floors. However here is (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  Re: MindStorms rotation sensors
 
Excuse me, I know this is an old post I am replying to, but I thought you might like to know... The proper phone # for orders from Pitsco Dacta is 800-835-0686. The number given in the posting is wrong (it should have been 888 ;-) and goes to an (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  FW: Worm Drive Question
 
G'Day How about a band or chain attached to the cab, then looped over a rotation sensor. Figure out the number of rotations ( or fractions there of) per floor and one sensor your done ! Cheers! Oliver. <<big snip ! >> (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  RE: Worm Drive Question
 
If you do not want to be limited to four floors you could have one long rod with "bumps" at every floor. With something sticking out of the elevator car, you know you have reached a floor everytime the rod is lifted from the ground. If you want to (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  RE: Worm Drive Question
 
But what I propose is initialize on ground floor Floor = 1 and then just go Floor=Floor+1 or Floor=Floor-1 each time you "feel" a bump. So you don't need "bits". It is less elegant, but it allows for more floors. I wonder if real elevators work like (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
 
  RE: Worm Drive Question
 
I take it all you merkins are on holiday? go and eat some Turkey and let me get some work done. ObLego: A Cleaner (and more expensive) way to do this is to mount the Sensors on the shaft and have them all plugged into the RCX when the lift gets to a (...) (28 years ago, 25-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR