To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6936 (+10)
  Re: Questions Regardsing Lego Scout
 
(...) (27 years ago, 17-Sep-99, to lugnet.robotics)
 
  Re: Questions Regardsing Lego Scout
 
Matthew Miller <mattdm@mattdm.org> wrote: [snip accidental posting] sorry about that -- hit wrong keys. (27 years ago, 17-Sep-99, to lugnet.robotics)
 
  RE: Light sensor values
 
One the raw note, my CdS cell (which measures about 20K ohms in the near dark, and about 500 ohms pointed at the florescent light) returns raw values between 1000 (pointed into a dark blue coffee cup) to 48 (pointed directly at the light with a (...) (27 years ago, 17-Sep-99, to lugnet.robotics)
 
  Re: Light sensor values
 
(...) dark, and about 500 ohms (...) into a dark blue coffee cup) to (...) this large dynamic range to (...) I have a CdS based light sensor but do not use it often because of the slow response to changing light conditions. I know CdS cells can vary (...) (27 years ago, 17-Sep-99, to lugnet.robotics)
 
  color sensor: was ( Light sensor values)
 
(...) It seems like you could get about 3-4 bits for each color if you were only using one input port. That's not very good resolution. Perhaps a better way would be to design a color sensor and use a pic chip for it's brain. It could sample all (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: Light sensor values
 
Richard <richard@mailstart.com> wrote in message news:FI88pu.4Js@lugnet.com... (...) when (...) cells? CdS sensors are pretty slow, but I don't think the ones I'm using take 5 seconds. I have used the Radio Shack 276-1657 and the Mouser 338-54C348 (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Motor Control
 
Hi everyone. I'm new to this site and was wondering if anyone has the information I need. 1)Who makes the UCN 5804 Uni-polar stepper driver and is it still made? 2)Where is a good place to find a wide selection of hobby size stepper motors on a (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: color sensor: was ( Light sensor values)
 
Pure-Lego (but more than one input/output unless a motor can be driven off of the output to a light sensor and the input from a light sensor and rotation sensor can be multiplexed): 1) 1 light sensor 2) 1 (micro)motor to drive the rotation of the (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: color sensor: was ( Light sensor values)
 
More simlple : use the sensor input mux by Michael Gasperi. You can easily connect 3 (up to 7) passive sensors to one RCX input. I've completed mine, but didn't test it already. "Stephen P. Gibbons" a écrit : (...) ---...--- Philippe Jadin (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: Motor Control
 
(...) There is probably no ready-to use chip to control a servo with a digital value. But you have two solutions : 1. Try to program a pulse width modulated signal output. You need a fast "brain"... 2. With an digital to analog converter and a 555 (...) (27 years ago, 18-Sep-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR